Although there are many techniques available to mitigate PCB resonances (e.g., board reinforcement, system damping, vibration isolation), a thorough analysis of the total mechanical system is still required. Finite element analysis (FEA) should be performed to identify all potential resonant modes and their associated frequencies and quality factors. Good design techniques can then be implemented to enhance performance.
in conclusion
This article reviews motion and understands the importance of MEMS inertial sensors in helping to overcome spatial orientation disorders. This article also discusses the adverse effects of poor or suboptimal placement, mounting conditions, and system resonances on MEMS inertial sensor performance. By following the correct design considerations, these "difficult" events can be "bypassed" and the performance of MEMS inertial sensors can be achieved.
Previous article:Choosing the best multi-core architecture for compute-intensive applications
Next article:CSR Bluetooth Networking Smart Home Solution
Recommended ReadingLatest update time:2024-11-15 02:10
- Red Hat announces definitive agreement to acquire Neural Magic
- 5G network speed is faster than 4G, but the perception is poor! Wu Hequan: 6G standard formulation should focus on user needs
- SEMI report: Global silicon wafer shipments increased by 6% in the third quarter of 2024
- OpenAI calls for a "North American Artificial Intelligence Alliance" to compete with China
- OpenAI is rumored to be launching a new intelligent body that can automatically perform tasks for users
- Arm: Focusing on efficient computing platforms, we work together to build a sustainable future
- AMD to cut 4% of its workforce to gain a stronger position in artificial intelligence chips
- NEC receives new supercomputer orders: Intel CPU + AMD accelerator + Nvidia switch
- RW61X: Wi-Fi 6 tri-band device in a secure i.MX RT MCU
Professor at Beihang University, dedicated to promoting microcontrollers and embedded systems for over 20 years.
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
- CGD and Qorvo to jointly revolutionize motor control solutions
- CGD and Qorvo to jointly revolutionize motor control solutions
- Keysight Technologies FieldFox handheld analyzer with VDI spread spectrum module to achieve millimeter wave analysis function
- Infineon's PASCO2V15 XENSIV PAS CO2 5V Sensor Now Available at Mouser for Accurate CO2 Level Measurement
- Advanced gameplay, Harting takes your PCB board connection to a new level!
- Advanced gameplay, Harting takes your PCB board connection to a new level!
- A new chapter in Great Wall Motors R&D: solid-state battery technology leads the future
- Naxin Micro provides full-scenario GaN driver IC solutions
- Interpreting Huawei’s new solid-state battery patent, will it challenge CATL in 2030?
- Are pure electric/plug-in hybrid vehicles going crazy? A Chinese company has launched the world's first -40℃ dischargeable hybrid battery that is not afraid of cold
- 【Infineon XENSIV PAS CO2 sensor】Arduino routine test
- [RISC-V MCU CH32V103 Evaluation] +RTC Usage
- Loongson decided to abandon all American technology and make a truly pure domestic instruction set
- Explosion-proof electromagnetic flowmeter integrated converter
- 【15th Anniversary】Want to meet up? Let's DIY an electronic tool box~You decide the functions
- [2022 Digi-Key Innovation Design Competition] Fully Automatic High-Pressure Steam Sterilization Controller - Unboxing
- The DAC output of the MCU is passed through the DAC0832
- What should I do if the current of the small motor is too large when it starts and the microcontroller is reset?
- MSP430 driver function for LCD1602
- Watch the video to win a JD card | Taixiang test of Shuige cheats