program:
#include "led.h"
void InitLed(void)
{
TRISB &= ~0x70;
ANSELB &= ~0x70;
}
void LedBlink(void)
{
u8 i;
for(i=0;i<3;i++){
LED0 = 1;LED1 = 1;LED2 = 1;
delay_10ms(400);
LED0 = 0;LED1 = 0;LED2 = 0;
delay_10ms(400);
}
}
void main()
{
InitLed();
LedBlink();
while(1)
{
LED1 = !LED1;
delay_10ms(100);
}
}
Disconnect the MOS tube and the inductor, the microcontroller can work normally, and the indicator light flashes 3 times normally. As shown below:
When the MOS tube is connected, the microcontroller cannot work normally and the indicator light is always on. As shown in the following figure:
Previous article:PIC microcontroller learning independent buttons
Next article:Two mistakes that beginners often make when using PICC
- Popular Resources
- Popular amplifiers
- Chip Manufacturing: A Practical Tutorial on Semiconductor Process Technology (Sixth Edition)
- singlechip-implementation-of-levelcrossing-adc-for-ecg-sampling-2332-0796-1000219
- Offline AC-DC Power Supply Design Guide Using BCDPWM Controller AP3103
- USB Complete The Developer\'s Guide 5ed (USB Development Complete 5th Edition)
Professor at Beihang University, dedicated to promoting microcontrollers and embedded systems for over 20 years.
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
- STM32F4 NVIC_SystemReset() function software reset fails due to external pull-up resistor on RST pin
- How to connect CC3200 to Gizwits Cloud
- MSP430Fr6972--AD usage summary
- 【Child care machine】+ ESP32-S3-BOX+ESP32-S3-DevKitC-1 material unpacking and BOX basic demonstration
- [Free trial of Pingtouge Bluetooth Mesh Gateway Development Kit] + nRF Mesh and Light Experiment (Part 2)
- PCB learning
- Allwinner V853 development board Tina SDK LCD small resolution DCLK setting problem
- Unboxing
- How to choose resistors in circuit design?
- A time-delayed shutdown circuit