• You can log in to your eeworld account to continue watching:
  • LIGHTING OUTLETS AT SWIMMING POOLS - 680.22(B)
  • Login
  • Duration:1 minutes and 22 seconds
  • Date:2022/09/28
  • Uploader:Lemontree
Introduction
keywords: electronic system
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

Unfold ↓

You Might Like

Recommended Posts

Pay attention to the packaging when applying for samples!
When you apply, please download the package in the same package! Pay attention to the suffix! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Reference AD8676ARZ 2 8 ld SOIC AD8675ARZ 2 8 ld SOIC AD5791BRUZ 1 20 ld TSSOP
蓝雨夜 ADI Reference Circuit
Using EMVC to create binary curves in ARM9 environment
How to make a real-time two-dimensional curve? Can an expert give the steps? Mainly how to display dynamic lines and coordinate lines on the interface.
liyanqing611 ARM Technology
DC motor driver.rar
DC motor driver.rar
yanghaibo1121 PCB Design
Thanks to chenzhufly, I finally got the SI1143 evaluation board
Because I want to test the performance of SI114X series sensors, I need an evaluation board. The evaluation boards from Silicon Labs are very expensive online, so I turned to look for the HID-USB-to-I
anning865 Sensor
Tips for getting started with ARM and embedded Linux
[i=s] This post was last edited by Patching on 2017-8-7 16:24 [/i] [color=#000][font=Simsun][size=3]Since many people always ask this question, here is a summary for your reference. It must be explain
补丁 Analog electronics

Recommended Content

Circuit

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews


Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号