• You can log in to your eeworld account to continue watching:
  • GROUNDING RECEPTACLES - 406.4(A)​​​​​​​
  • Login
  • Duration:4 minutes and 29 seconds
  • Date:2022/09/28
  • Uploader:Lemontree
Introduction
keywords: electronic system
Switchboards are designed with busbars for fuses or circuit breakers that are used for protecting and supplying feeders and branch circuits. Panelboards are designed with a permanently installed main circuit breaker or single set of fuses for disconnecting the number of circuit breakers or fuseholders installed to protect and supply feeders or branch circuits.

SUPPORT AND ARRANGEMENT OF BUSBARS AND CONDUCTORS
408.3

Busbars shall be held firmly in place in the enclosure and shall be arranged in such a way to allow adequate space for conductors to be terminated. Busbars shall be sized with enough capacity to handle the normal currents in amps of the electrical system. In addition, they shall carry safely any type of short-circuit or ground-fault condition.

CONDUCTORS AND BUSBARS ON A SWITCHBOARD OR PANELBOARD
408.3(A)

Conductors and busbars on a switchboard, panelboard, or control board shall be so located as to be free from physical damage. Service sections of such boards shall be separated from the other electrical components. These components shall be properly secured in an approved manner. 

Note, conductors entering a certain section shall terminate in such section, except where it is not practical for control, interconnecting conductors, or other conditions of use.

OVERHEATING AND INDUCTIVE HEATING
408.3(B)

The arrangement of busbars and conductors shall be such as to avoid overheating due to inductive effects. The inductive effect of each conductor is neutralized when grouping all conductors together. To accomplish the minimizing of heating effects, the ungrounded (phase) conductors, grounded (neutral) conductors, and equipment grounding conductors, where used, shall be in the same enclosure, raceway, cable, cord, etc. (See Figure 7-1)

Unfold ↓

You Might Like

Recommended Posts

[Social Recruitment/Campus Recruitment] [Institute of Software, Chinese Academy of Sciences] FPGA R&D Engineer
[align=left][size=14px][font=微软雅黑] [/font][/size][/align][align=left][size=14px][font=微软雅黑]Due to work needs, we plan to recruit a number of scientific researchers with preferential treatment. Fresh g
ninglu Recruitment
EEPROM
How to write data to EEPROM in 9S12
hsleung NXP MCU
One minute to understand: World Industrial History (video explanation)
Industry is to quickly produce a large number of goods needed by humans, forming a set of specialized production models, and effectively improving production efficiency. What developments has the worl
成都亿佰特 maychang Fun Electronics
Application of MCGS configuration software in water supply automation monitoring system
This paper briefly introduces the MCGS configuration software and its application in the "Xinjiang Tahe Oilfield Water Supply Project Monitoring System", and explains the basic process of using MCGS c
frozenviolet Security Electronics
EEWorld's "Search Device" applet is now online, allowing you to easily check device data and make chip selection easier
EEWorld "Search Device" applet 1.1 updated, adding a new "note" function to record device thoughts; search function further optimized to understand you better~Instant query of data sheets for tens of
EE大学堂 Integrated technical exchanges
Hezhongda 28335 development board schematic diagram and source code
Hezhongda 28335 development board schematic and source code
hust4q DSP and ARM Processors

Recommended Content

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews


Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号