In recent years, Enceladus has attracted much attention due to the fact that it contains an ocean system beneath its surface ice.
In a 17-year collaboration, researchers at Carnegie Mellon University (CMU) and NASA's Jet Propulsion Laboratory have created an autonomous, snake-like robot , the Exobiology Extant Life Surveyor (EELS).
NASA scientists said they hope to use the EELS robot to search for signs of life in the ocean beneath the icy crust of Enceladus. The related paper was also published in Science Robotics and was featured on the cover of the March issue.
Snake robots have always been considered the first choice for activities in narrow and complex environments. Compared with traditional robots, they can move freely in areas with many obstacles with their slender bodies with dozens of hinged joints.
After several years of preparation, EELS brings together the wisdom of many universities including Carnegie Mellon University, Arizona State University and University of California, San Diego, and demonstrates the most cutting-edge robotics technology.
EELS is about 4 meters long and consists of 10 identical parts, with a total weight of about 100 kilograms. Each section contains 3 actuators, the first two are used to adjust the shape, and the last one controls the advancement of the surface thread. Each shape actuator can provide a peak torque of up to 400N·m, giving EELS a wide range of degrees of freedom.
The unique self-repeating structure gives EELS excellent mobility. It can avoid obstacles by means of serpentine twists and turns, and can also quickly cross flat areas through active skin thread propulsion.
Looking at the system architecture of EELS, its control module adopts a layered architecture, which helps to disassemble complex problems and maintain code. The control level rises from the bottom-level hardware instructions to the high-level task goals, and each level controller decomposes and translates the intentions of the previous level. For example, the actuator controller will convert the screw speed, shape, etc. required by the upper level into specific actions that can be executed by the hardware.
According to Professor Howie Choset, a research scientist on the project, "The benefit of snake robots is that they can use their many joints and slender physiques to move through tightly packed volumes and reach locations that robotic operatives cannot reach."
Even in extreme environments such as ice, sand, rocks, cliffs, etc., EELS can still pass freely. EELS will also use these capabilities to crawl into the cracks of Enceladus' ice layer, which will help the robot move better on the ice until it finds a crack or geyser hole to crawl into.
In addition, the "wheels" of EELS are also very special. Unlike other snake-like robots, it is more like a "bottle opener" than a "wheel".
"As these corkscrews rotate, they penetrate the ice a little bit, but also enable the mechanism to roll forward. So the robot has the ability to propel itself, not only with a serpentine motion, but these corkscrew wheels allow it to move across icy surfaces very quickly."
Previous article:Two robot companies failed in their A-share IPOs
Next article:Two cases of financing in half a month, mobile robots are "a blessing after a long drought"
- Popular Resources
- Popular amplifiers
- Using IMU to enhance robot positioning: a fundamental technology for accurate navigation
- Researchers develop self-learning robot that can clean washbasins like humans
- Universal Robots launches UR AI Accelerator to inject new AI power into collaborative robots
- The first batch of national standards for embodied intelligence of humanoid robots were released: divided into 4 levels according to limb movement, upper limb operation, etc.
- New chapter in payload: Universal Robots’ new generation UR20 and UR30 have upgraded performance
- Humanoid robots drive the demand for frameless torque motors, and manufacturers are actively deploying
- MiR Launches New Fleet Management Software MiR Fleet Enterprise, Setting New Standards in Scalability and Cybersecurity for Autonomous Mobile Robots
- Nidec Drive Technology produces harmonic reducers for the first time in China, growing together with the Chinese robotics industry
- DC motor driver chip, low voltage, high current, single full-bridge driver - Ruimeng MS31211
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
- CGD and Qorvo to jointly revolutionize motor control solutions
- CGD and Qorvo to jointly revolutionize motor control solutions
- Keysight Technologies FieldFox handheld analyzer with VDI spread spectrum module to achieve millimeter wave analysis function
- Infineon's PASCO2V15 XENSIV PAS CO2 5V Sensor Now Available at Mouser for Accurate CO2 Level Measurement
- Advanced gameplay, Harting takes your PCB board connection to a new level!
- Advanced gameplay, Harting takes your PCB board connection to a new level!
- A new chapter in Great Wall Motors R&D: solid-state battery technology leads the future
- Naxin Micro provides full-scenario GaN driver IC solutions
- Interpreting Huawei’s new solid-state battery patent, will it challenge CATL in 2030?
- Are pure electric/plug-in hybrid vehicles going crazy? A Chinese company has launched the world's first -40℃ dischargeable hybrid battery that is not afraid of cold
- [GD32L233C-START Review] 1. GD32L233C-START with obvious advantages and disadvantages (unboxing)
- LTC2325-16 Sampling Issues
- Design considerations for single-chip microcomputer key scanning program
- How to change the library file in the schematic diagram in orcad?
- Free application: Domestic FPGA Gaoyunjia Little Bee Family GW1N Series Development Board
- Taking stock of the college entrance examination experience of Internet tycoons! How many points did you get in the exam?
- Without American EDA software, we can’t make chips?
- 【Share】Flash management tools: FAL (Flash Abstraction Layer) library
- [Awards awarded] Grab the post! Download the TWS headset white paper, write a wonderful review, and win a JD card!
- Constant voltage circuit and constant current circuit composed of operational amplifier and triode