Product DescriptionMS31211
is a low voltage, high current, single full bridge driver. It can be used in low voltage and battery powered motion control applications, and has a built-in charge pump to provide the gate drive voltage required by the internal power NMOS.MS31211
can provide a peak current of up to 3.2A, its power supply range is from 1.8V to 10V, and the logic supply range is from 1.8V to 6V.
Two input pins can control the DC motor to work in forward, reverse, brake and coasting modes.The full bridge is controlled by IN1/IN2 logic, and enters standby mode when all INx=0V for more than 3ms.
Main features
① Single full-bridge driver, low output on-resistance, 240mΩ (HS+LS)
② 3.2A peak current capability
③ Power supply range: 1.8V to 10V
④ Logic supply range: 1.8V to 6V
⑤ IN1/IN2 full-bridge control logic
⑥ In standby mode, power consumption does not exceed 120nA@VM<6V ⑦
eMSOP10 package (back heat sink), 3mmx3mm
⑧ Protection function: undervoltage protection, overtemperature protection
Application
① Camera
② Toy
③ Robot
④ Portable medical electronic equipment
Functional Description
The MS31211 is a low voltage, single full-bridge driver that can be used to drive a DC motor.
Full-bridge control logic
Standby mode
The MS31211 provides a standby mode. When the time when IN1=IN2=0 exceeds 3ms, the chip will enter the standby mode. In standby mode, all modules of the chip will be turned off. If one of the INx pins is pulled high, the chip will enter the normal working mode from the standby mode.
The power supply and input pins
VDD and VM can be powered on or off in a non-sequential manner. When VDD is powered off, the chip will enter a low power state, at which point VM consumes only a small current. If the VM voltage is between 1.8V and 6V, VDD and VM can be connected together externally for power supply.
Protection circuit
The MS31211 provides protection circuits, including undervoltage protection, overtemperature protection, etc. In the protection state, the nFAULT pin will be pulled low.
Recommended operating parameters
This model requires a minimum operating voltage of 1.8V to work. While supporting low voltage, it can also provide a large drive current (3.2A maximum). It is low cost and has a wide range of applications, such as electric curtains, toys, robots, etc. MS31211 has been shipped in large quantities, and samples are welcome. Xinbangwang-Nong S18025319604
Previous article:The world's first humanoid robot factory goes into production, with an annual production target of 10,000 units, ushering in a new blue ocean for components
Next article:Nidec Drive Technology produces harmonic reducers for the first time in China, growing together with the Chinese robotics industry
- Popular Resources
- Popular amplifiers
- Using IMU to enhance robot positioning: a fundamental technology for accurate navigation
- Researchers develop self-learning robot that can clean washbasins like humans
- Universal Robots launches UR AI Accelerator to inject new AI power into collaborative robots
- The first batch of national standards for embodied intelligence of humanoid robots were released: divided into 4 levels according to limb movement, upper limb operation, etc.
- New chapter in payload: Universal Robots’ new generation UR20 and UR30 have upgraded performance
- Humanoid robots drive the demand for frameless torque motors, and manufacturers are actively deploying
- MiR Launches New Fleet Management Software MiR Fleet Enterprise, Setting New Standards in Scalability and Cybersecurity for Autonomous Mobile Robots
- Nidec Drive Technology produces harmonic reducers for the first time in China, growing together with the Chinese robotics industry
- DC motor driver chip, low voltage, high current, single full-bridge driver - Ruimeng MS31211
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
- CGD and Qorvo to jointly revolutionize motor control solutions
- CGD and Qorvo to jointly revolutionize motor control solutions
- Keysight Technologies FieldFox handheld analyzer with VDI spread spectrum module to achieve millimeter wave analysis function
- Infineon's PASCO2V15 XENSIV PAS CO2 5V Sensor Now Available at Mouser for Accurate CO2 Level Measurement
- Advanced gameplay, Harting takes your PCB board connection to a new level!
- Advanced gameplay, Harting takes your PCB board connection to a new level!
- A new chapter in Great Wall Motors R&D: solid-state battery technology leads the future
- Naxin Micro provides full-scenario GaN driver IC solutions
- Interpreting Huawei’s new solid-state battery patent, will it challenge CATL in 2030?
- Are pure electric/plug-in hybrid vehicles going crazy? A Chinese company has launched the world's first -40℃ dischargeable hybrid battery that is not afraid of cold
- L298N output voltage problem
- HGIT Fights Epidemic-After-sales Technical Exchange
- KiCad KiCost GOOD
- Support Xilinx/Altera/Lattice JTAG and UART
- R329 development board series tutorial | Running aipu program on real machine
- Angle, distance, speed, and direction of motion detection can be done on one board. Infineon's FMCW radar solution Position2Go is here
- PWM issues with MSP432
- Is there any MP3 decoding library?
- MicroPython has over 10,000 stars on GitHub!
- MSP430G2553 State Machine Modeling