SPMC65P2404A/SPMC65P2408A Chinese data, pdf datasheet (Micro-Controllers (OTP) With ADC)

Recommended ContentMore

Open source project More

• Flash card holder
• MAXREFDES48#: 24V to 12V, 40W isolated power supply with EFD20 core transformer
• 51 microcontroller-love lamp
• HotBed
• USB adapter
• DER-857 - 65 W high power factor, isolated flyback and switch valley-fill PFC LED driver based on LYTSwitch-6 with PowiGaN technology
• NCV891330PD38GEVB: 3 A, 2 MHz low Iq dual-mode buck regulator evaluation board
• [Internet of Things] Hongmeng wifi switch
• Voice controlled melody light
• SW3518S 100W full protocol fast charging source

Searched by Users

• 【TI】drv8412: Dual brushed DC or single bipolar stepper motor driver (PWM controller)
• Neural Networks and Deep Learning (Michael Nielsen)
• Making a Simple FM Radio Using 6J8P Electron Tube
• GB 50058-1992 Design specification for electrical installations in explosive and fire hazardous environments.pdf
• USB to TTL-CP2102 driver
• PCB package library download
• VSPD 6.9 virtual serial port cracked version
• Font reading software! You can take a look at this very useful MTK software reading tool!
• CANopen Source Code
• proe5.0 Wildfire version download (Chinese version free download)

Just Take a LookMore

• 【ufun learning】Analysis of the buzzing routine
  Buzzer is a good device used by microcontrollers to alert people.I am more interested in this MLT-5020 because I have studied buzzing, and the bigger the buzzer, the louder it is. As can be seen from
• Design and simulation of LC balun
  [i=s]This post was last edited by qwqwqw2088 on 2019-11-21 11:52[/i]Balun (Balun: Balance-UnBalance) can achieve the conversion between single-ended and differential structures. However, the cheapest
• Capacitive touch MSP430FR2676 MCU motherboard
  The MSP430FR2676 CapTIvate Touch MCU Board (CAPTIVATE-FR2676) is a simple evaluation board for evaluating capacitive touch and proximity sensors using plug-in sensor boards (sold separately).The MCU b
• 【XMC4800 Relax EtherCAT Kit Review 2】-Building the environment and lighting up the LED
  [i=s]This post was last edited by tdatd on 2019-1-2 11:13[/i] [align=left][align=left]Go to the evaluation application interface[size=7.5pt] [/size][url=https://en.eeworld.com/bbs/elecplay/content/100
• Common problems in OLED development
  1.Installation There are usually three ways to install OLED:1). Because it is relatively thin, it can usually be glued to the PCB with double-sided tape or foam tape.2). If you have higher requirement
• ECG monitor solution based on DSP system platform
• A novice asks about AD copper plating, thank you
• Compact W600 development board
• Introduction and basic concepts of antennas commonly used in daily EMC and RF testing
• Amplifier Circuit

Trending Downloads

• I will post another piece of information about thermal resistance, which I think is more useful.
• Research on key technologies of MPEG-4 decoding and its implementation on FPGA
• ARM+MP3+USBHOST(at91sam7s64+vs1003b+ch375v) is a program that allows you to program the audio and video files of your choice.
• chapter 09
• ARM JTAG Real-time Emulator Installation and Usage Guide
• 1000MY96
• Design of four-character LED display based on AT89C2051
• Journal article: Transient component detection and application based on continuous wavelet and statistical test
• C++ program to solve the system of equations by using chord cutting in numerical calculation
• C language example materials

Trending ArticlesMore

• Semiconductor reliability testing will become a new core business
• Practice | How to implement PCIe Gen3/Gen4 receiver link equalization test?
• AIIA: Open source empowerment, intelligent sharing
• News: Brice Hill officially takes up new post as Xilinx CFO
• How to accelerate artificial intelligence in smartphones? Micron has a "big trick"!
• Make every effort to build "Nanjing's Silicon Valley" (Photo)
• 【Job Featured】Senior Stamping Engineer - Suzhou
• This is definitely something you have never seen before --- leakage circuit breaker