Altium Designer 4-layer smart car complete PCB design video tutorial

Altium Designer 4-layer smart car complete PCB design video tutorial

Many novices in electronic design or college graduates are confused like this: what is taught in school is usually theoretical, and hands-on practical operations may not be very important. When you first enter the job, it is completely the opposite. Practical skills need to be placed first. , but how to learn these practical skills? Self-study is not only inefficient, but also I don’t know how to start.

In response to this situation on the market, Fanyi Education, as a leader in electronic design online education, timely launches this set of full-process electronic design practical videos to meet the learning needs of students.

This set of tutorials uses the new version of Altium Designer to explain in stages. From creating schematic libraries, schematics, PCB libraries to layout and routing of PCB design, the whole process is explained and communicated with everyone. How to draw each device? How is it placed? How to pull each wire? What are the power cords? What are signal lines? These will be explained in detail one by one, and novices can generally do it themselves after reading it once. The entire process from scratch is explained clearly, so that as a novice, you can really learn something.

• Chapter 1：Course Introduction (23 minutes and 46 seconds)

• Chapter 2：Electronic design learning ideas (15 minutes and 24 seconds)

• Chapter 3：AD software installation and switching between Chinese and English (13 minutes and 59 seconds)

• Chapter 4：AD project composition and creation (10 minutes and 27 seconds)

• Chapter 5：Introduction to component library and creation of resistor and capacitor model (18 minutes and 14 seconds)

• Chapter 6：Creation of IC component models (18 minutes and 4 seconds)

• Chapter 7：Creation of pin header component model (8 minutes and 22 seconds)

• Chapter 8：Creation of optocoupler and diode component models (17 minutes and 43 seconds)

• Chapter 9：Calling existing component models (11 minutes and 44 seconds)

• Chapter 10：Placement of components (4 minutes and 52 seconds)

• Chapter 11：Device duplication and alignment (22 minutes and 36 seconds)

• Chapter 12：Adding wires and NetLabel (51 minutes and 21 seconds)

• Chapter 13：Value check (11 minutes and 20 seconds)

• Chapter 14：Unified management of packages (9 minutes and 0 seconds)

• Chapter 15：Compilation settings and inspection of schematic diagram (13 minutes and 53 seconds)

• Chapter 16：Creation of common CHIP packages (24 minutes and 21 seconds)

• Chapter 17：Creation of common IC type packages (15 minutes and 35 seconds)

• Chapter 18：Use the IPC package creation wizard to quickly create packages (12 minutes and 24 seconds)

• Chapter 19：Direct call of commonly used PCB packages (8 minutes and 30 seconds)

• Chapter 20：Creation and import of 3D models (17 minutes and 53 seconds)

• Chapter 21：Solutions to common import errors (27 minutes and 52 seconds)

• Chapter 22：Elimination of common green errors (12 minutes and 2 seconds)

• Chapter 23：PCB frame evaluation and stackup setup (24 minutes and 34 seconds)

• Chapter 24：PCB shortcut key settings and recommendations (19 minutes and 41 seconds)

• Chapter 25：Modular layout planning (10 minutes and 22 seconds)

• Chapter 26：PCB layout practical demonstration 1 (31 minutes and 57 seconds)

• Chapter 27：PCB layout practical demonstration 2 (18 minutes and 42 seconds)

• Chapter 28：PCB layout optimization and adjustment (9 minutes and 26 seconds)

• Chapter 29：Creation of Class, design parameters, and rules (38 minutes and 41 seconds)

• Chapter 30：Processing of fan holes and application of copper-clad plug-ins (31 minutes and 36 seconds)

• Chapter 31：PCB Laying - Signal Line Routing (9 minutes and 54 seconds)

• Chapter 32：PCB wiring - wiring of the power supply section (18 minutes and 48 seconds)

• Chapter 33：Signal line trimming optimization and GND processing (25 minutes and 22 seconds)

• Chapter 34：DRC inspection and silk screen adjustment (28 minutes and 44 seconds)

• Chapter 35：What is imposition & why imposition is necessary (9 minutes and 15 seconds)

• Chapter 36：The concept of V-cut and stamp hole puzzle (9 minutes and 26 seconds)

• Chapter 37：Practical demonstration of puzzle pieces (18 minutes and 4 seconds)

• Chapter 38：Output and sorting of Gerber files (33 minutes and 2 seconds)