Small signal measurements in noise

Power: Power

Noise floor after oversampling: Noise floor after oversampling

orignal noise floor: initial noise layer

frequency: frequency

Oversampling ratio: oversampling ratio

The delta-sigma converter can accurately measure the analog input by using an integrator in the modulator control loop to perform noise shaping. The noise shaping process of the integrator is to force more noise to higher frequencies, as shown in Figure 3. The digital low-pass filter then removes the high frequency portion of the noise, which greatly improves the SNR. The digital filter can also be used to greatly reduce noise at 50Hz, 60Hz or other unwanted frequencies.

Figure 3: The integrator forces the noise to a higher frequency

Signal Amplitude : Signal amplitude

Digital Filter Rsponse: Digital filter response

power: power

1. The integrator forces the noise out of the frequency band of interest;

2. Digital filter filters out high-frequency noise

frequency: frequency

Oversampling ratio: oversampling ratio

There will always be some noise in the digital bit stream from the input signal. But through averaging and filtering, delta-sigma ADCs significantly reduce the noise floor. The oversampling ratio and the "order" of the internal delta-sigma modulator determine the noise level. The term order refers to the number of integrators. For example, a 3rd order modulator has 3 integrator stages.

Although adding integrator stages and increasing oversampling ratios can further reduce noise, stability is a major concern for 3rd-order or higher delta-sigma converters. Once delta-sigma modulators become unstable, they often do not become stable again unless power is cycled. All Linear Technology delta-sigma converters use 3rd-order modulators, and the modulator and filter are reset for each conversion. Even if the modulator becomes unstable (which is likely to happen with low reference voltages and large input signals), Linear Technology's delta-sigma ADCs can restore stability on their own without periodically cycling power, which may not be possible with other ADCs.

After the modulator loop is stable and the noise is shaped by the integrator, the next step is to filter and decimate the generated digital signal. Decimation is to discard some samples, mainly to remove redundant signal information caused by oversampling. If the oversampling rate is 256, the ADC takes the average of 256 samples, and the decimator produces 1 digital output for every 256 samples. The digital signal generated after filtering and decimation is then output from the ADC, which adopts a serial format.

The digital output of a delta-sigma ADC is only as good as its reference. A noisy reference is a major source of error in any data converter. The 1-bit DAC of a delta-sigma modulator is biased by a positive and a negative reference voltage. The positive (or high) reference voltage is generally the upper limit of the input range, while the negative (or low) reference voltage is generally the lower limit. Some delta-sigma ADCs have both the positive and negative references connected externally, while others have the low reference connected to a common voltage, such as ground. Other ADCs have the option of using an internal bandgap reference or an external reference. Linear Technology's delta-sigma converters allow the designer to vary the reference and input common-mode voltages from ground all the way up to the supply voltage.

Conversion clock and data latency are two important factors to consider when selecting a delta-sigma converter. The clock controls the internal timing of data processing and determines the conversion time. The conversion clock can be provided internally or from an external crystal or silicon oscillator. However, since the digital filter does not suppress the oscillator frequency, there is an advantage to using an internal oscillator.

Due to data delays, the current output result lags behind the input by one sampling cycle. All of Linear Technology's No Latency Delta Sigma™ converters settle within one cycle, simplifying multiplexed applications.

Although the delta-sigma ADC is simple in nature, configuring this ADC is often a complex process, such as writing many instructions, balancing the complexity of the input stage and selecting an external oscillator. Linear Technology's delta-sigma converters have no calibration sequence, configuration registers, filter stabilization time and external oscillator, reducing the complexity of the design. Transparent offset and full-scale automatic calibration are performed in each conversion cycle to ensure high accuracy, which guarantees the ability to distinguish differences of 1 gram or 0.01 degree.