MPQ24S48-50 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > MPQ24S48-50

Preview

MPQ24S48-50: Description50 W DC-DC Converter 10-36 Vdc Input 48 Vdc Output at 1 A Quarter-Brick Package; File Size580KB，11 Pages; ManufacturerWall Industries,Inc.; Websitehttps://www.wallindustries.com/

Download Datasheet Compare View All

MPQ24S48-50 Overview

50 W DC-DC Converter 10-36 Vdc Input 48 Vdc Output at 1 A Quarter-Brick Package

Preview

Download Datasheet

View All

TECHNICAL DATASHEET

Rev. B

MPQ24S48-50

50 W DC-DC Converter

10-36 Vdc Input

48 Vdc Output at 1 A

Quarter-Brick Package

Features:

•

Over 87% Efficient at Full Load

•

Fast Transient Response

•

Operation to No Load

•

Output Trim +/-10%

•

Remote ON/OFF

•

Remote Sense Compensation

•

Low Output Ripple

•

Fixed Switching Frequency

Output Over Current Protection

Output Short Circuit Protection

Over Temperature Protection

1000 V Isolation

100% Burn In

Heatsink Available

Description:

The MPQ24 series is a high density, low voltage input quarter brick converter that incorporates the

desired features required in today’s demanding applications while maintaining low cost. When

performance, reliability, and low cost are needed, the MPQ series delivers.

(888) 597-WALL

www.wallindustries.com

1 of 11

WALL INDUSTRIES, INC.

DESIGN CONSIDERATIONS

Under Voltage Lock Out (UVLO)

Rev. B

TECHNICAL DATASHEET

MPQ24S48-50

The converter output is disabled until the input voltage exceeds the UVLO turn-on limit. The converter will remain ON until the input

voltage falls below the UVLO turn-off limit.

Over Current Protection

The converter is protected from short circuit and over current conditions. Upon sensing an over current, the output will begin to drop (or

‘foldback’) limiting the output power. Further increasing the output current will cause the converter to shut off and then restart (or

‘hiccup’) until the overcurrent condition is removed. Shorting the output will cause the converter to immediately enter the ‘hiccup’ mode.

Over Temperature Protection

The converter is protected from over temperature conditions. Upon exceeding this temperature, the converter will shut down. The

converter will automatically recover once the over tempature condition is removed.

Input Filter

No additional input capacitor is needed for the power supply to operate. However, due to the low voltage, high input current nature of the

power supply, it is highly recommended that a minimum 100 uF/50 V electrolytic type input bulk capacitor be added to reduce input

ripple voltage and current. Refer to Photos 1 and 2 for an example. For an even further reduction of input ripple, an inductor may be

placed between the source and the previously mentioned capacitor. Additionally, a 1-10 uF ceramic capacitor may be added in front of

the inductor to form pi-filter. No inductor should be placed between the capacitor and the input to the converter.

Output Filter

No additional output capacitor is needed for the power supply to operate. However, to reduce the ripple and noise on the output,

additional capacitance may be added. Usually, a ceramic capacitor between 0.1 and 1 uF is recommended for reducing any ringing and

spike noise. Also, capacitance in the form of an aluminum electrolytic capacitor may also be placed across the output in order reduce

ripple, and improve the transient peak-to-peak voltage deviation (see

Photos 7 to 11),

but in most cases, is not necessary.

Remote Sense

To improve regulation at the load, route the connections from the -Sense and the +Sense pins to the –Vout and +Vout connections at the

load. This will force the converter to regulate the voltage at the load and not at the pins of the converter. If it is not desired to use the

Remotes Sense feature, the –Sense and +Sense pins should be shorted to the -Vout and +Vout pins respectively. However, no damage to

the converter will occur if the Sense pins are left open.

Fusing

It is required that the input to the converter be supplied with a maximum 10 A, 250 V rated fuse UL Listed or R/C fuse.

Safety

The MPQ24 series is designed to meet EN60950 Safety of Information Technology Equipment. The isolation provided by the MPQ24

series is a Basic insulation in accordance with EN60950. SELV output reliability is maintained only if the input to the converter is a

SELV source. To maintain SELV reliability, if either +Vin or –Vin is connected to chassis, either +Vout or –Vout must also be

connected to chassis. Otherwise, both the input and the output must not be connected to chassis.

PCB Layout Considerations

Due to the Basic isolation provided by the converter, caution must be observed in routing traces more than 2 mm inward of any input or

output pins on the top layer of the pcb board underneath the converter. Also, due to noise coupling and isolation requirements, no power

or ground planes or any signal traces should be routed on the top layer of the pcb underneath the converter. Due to comon noise coupling,

input or output power and ground planes should not be poured across the input to output on any layers underneath the converter. Instead,

it is best to provide separate input and output power and ground traces on the bottom or an inner layer with a miminum of 1 mm

separation between traces on the same layer.

Lastly, as the case/heatsink is floating metal, caution must also be observed to provide appropriate spacing (minimum 1.4 mm for

Pollution degree 2 Material Group IIIa + IIIb) around the case/heatsink or risk reducing the input to output spacing and violating Basic

insulation requirements.

(888) 597-WALL

www.wallindustries.com

Page 4 of 11

MPQ24S48-50 Related Products

	MPQ24S48-50	MPQ24S48-50C	MPQ24S48-50R
Description	50 W DC-DC Converter 10-36 Vdc Input 48 Vdc Output at 1 A Quarter-Brick Package	50 W DC-DC Converter 10-36 Vdc Input 48 Vdc Output at 1 A Quarter-Brick Package	50 W DC-DC Converter 10-36 Vdc Input 48 Vdc Output at 1 A Quarter-Brick Package

Recommended Resources

Lithium-Ion Battery Overview

Design of adjustable DC stabilized power supply circuit module

Thyristor automatic charger circuit

Control circuit using NE555 integrated circuit_1

Pocket gas alarm

LED-parallel LED digital tube static display circuit (common anode)

Detailed interpretation of Brilliance 1.8T power system: Forward: When it comes to engines, the Chinese people are filled with pain. China's automobile industry has gone through fifty years of ups and downs, but these fifty years have been ridiculed by fore...; gaoyanmei Automotive Electronics

Get a gift for your evaluation! Hands-on experience: Recruiting TI millimeter-wave radar testers from all over the Internet: Get a gift for your evaluation! Hands-on experience: Recruiting TI millimeter-wave radar testers from all over the InternetClick here to enter the eventEvent timeDevelopment board application: now - N...; EEWORLD社区 TI Technology Forum

Comparison between digital TV and IPTV: ...; ayou

How does Allegro's built-in package library identify which type of device it belongs to?: In the package library that comes with Allegro, CAP400 and CAP300 are different packages for capacitors, and RES500 and RES600 are different packages for resistors. The question I want to ask is, in t...; ujs PCB Design

General Design Considerations for Embedded Systems: Our lives are filled with an ever-increasing number of tiny battery-powered devices and systems. These embedded systems must be powered by the same power supply for a long time to reduce recurring mai...; Aguilera Microcontroller MCU

CH340 circuit improves working stability and anti-interference: [size=4][color=#000000][backcolor=white] Because USB signals are analog signals, the CH340 and other USB chips contain digital circuits and some analog circuits. In addition, the USB chip also contain...; fish001 Analogue and Mixed Signal

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components