Forum»Forum › FPGA/CPLD › ZYNQ cannot be burned to NAND Flash via JTAG

5146 views|8 replies

19 Posts	0 Resources

The OP

Published on 2019-8-8 23:43 Only look at the author

ZYNQ cannot be burned to NAND Flash via JTAG [Copy link]

The board used is the EBAZ4205 mining board. I compiled the uboot myself and wanted to burn it into NAND. When burning, the following prompt appeared. The burning was unsuccessful and it was always "failed -12"

NAND write: device 0 offset 0x200000, size 0x12800

NAND write to offset 200000 failed -12

0 bytes written: ERROR

Zynq> Program Operation successful.
INFO: [Xicom 50-44] Elapsed time = 23 sec.

Flash Operation Successful

This post is from FPGA/CPLD

Latest reply

littleshrimp

NAND needs to be configured in ZYNQ system Details Published on 2020-4-3 23:22

FPGA论坛 CPLD论坛 FPGA教程

chenzhufly

5979 Posts	8 Resources

Published on 2019-8-9 11:30 Only look at the author

Is the address correct?

You can look at my post

This post is from FPGA/CPLD

Comments

duanks

It's fine after changing to 2018.3. 2019.1 seems to have problems, because it is OK to use the built-in NAND read and write routines Details Published on 2019-8-10 19:21

Personal signature生活就是油盐酱醋再加一点糖，快活就是一天到晚乐呵呵的忙
===================================
做一个简单的人，踏实而务实，不沉溺幻想，不庸人自扰

FPGA培训 FPGA设计 verilog教程

duanks

19 Posts	0 Resources

The OP| Published on 2019-8-10 19:21 Only look at the author

chenzhufly posted on 2019-8-9 11:30 Is the address correct? You can take a look at my post

It's fine after changing to 2018.3. 2019.1 seems to have problems, because it is OK to use the built-in NAND read and write routines

This post is from FPGA/CPLD

chenzhufly

5979 Posts	8 Resources

Published on 2019-8-10 21:37 Only look at the author

How big is it? Share it.

This post is from FPGA/CPLD

后来小生

6 Posts	0 Resources

Published on 2020-3-26 18:16 Only look at the author

?????

This post is from FPGA/CPLD

后来小生

6 Posts	0 Resources

Published on 2020-3-26 18:16 Only look at the author

Can I download it? I also encountered this problem.

This post is from FPGA/CPLD

后来小生

6 Posts	0 Resources

Published on 2020-3-26 18:17 Only look at the author

I don't know if it's solved.

This post is from FPGA/CPLD

后来小生

6 Posts	0 Resources

Published on 2020-3-26 22:15 Only look at the author

Has the landlord solved it?

This post is from FPGA/CPLD

Comments

littleshrimp

Need to configure NAND in ZYNQ system Details Published on 2020-4-3 23:22

littleshrimp

9702 Posts	24 Resources

Published on 2020-4-3 23:22 来自手机 Only look at the author

Later, Xiaosheng published on 2020-3-26 22:15 Did the OP solve it?

NAND needs to be configured in ZYNQ system

This post is from FPGA/CPLD

Return list

Guess Your Favourite

Just looking around

Solution to the problem of NAND write to offset xxxx failed -12 when burning NAND FLASH on ZYNQ
WhenusingVivadotoburnNAND,italwayspromptsNANDwritetooffsetxxxxfailed-12Because2018Asaresult,2018https://bbscomthread-1085626-1-1.htmlIdon'tknowwhythishappensUndernormalcircumstances,youcanuseallthefilesof20193,andselectallthefilesgeneratedb ...
When burning MCU firmware from Jlink V7.90 to the latest version of J-flash, the MCU flash base address cannot be changed
WhenthenewversionofJ-flashisburningMCUfirmware,theMCUflashbaseaddresscannotbechanged.1OnlyJlinkafterv7Thejlinksoftwarebeforev7Pleasedon'tbothermeifyousaydowngradetheversion!2ItisanoutdoortestTherearethousandsofKeilprojectfilesThedevelopment ...
OPEN SCOFIELD WINTER WARDROBE
[img]https://wwwnet/images/2024/11/14/1f9dff95d3bc981f8img][img]https://wwwnet/images/2024/11/14/2a81ca07f0c52991bimg]
Newbie Report Newbie Report
How to use CAN communication to control the inverter?
C language STM8 program help
Will Wi-Fi 6 replace Wi-Fi 5 as the mainstream wireless standard?
Why is the RAM compiled by IAR larger than the specification? ? It can also run normally
Today's live broadcast: The new Infineon MOSFET based on Source-down technology effectively improves power density, which is visible to the naked eye
DIY a WS2812 clock

Find a datasheet?

EEWorld Datasheet Technical Support

Hot tag

Related articles more>>

Qualcomm launches its first RISC-V architecture programmable connectivity module QCC74xM, supporting Wi-Fi 6 and other protocols
On November 14, Qualcomm announced the launch of two connectivity modules, QCC74xM and QCC730M, f
It is reported that memory manufacturers are considering using flux-free bonding for HBM4 to further reduce the gap between layers
On November 14, according to Korean media ETNews, Samsung Electronics, SK Hynix, and Micron are a
ON Semiconductor CEO Appears at Munich Electronica Show and Launches Treo Platform
During Electronica, ON Semiconductor CEO Hassane El-Khoury was interviewed by Power Electronics N
AMD launches second-generation Versal Premium series: FPGA industry's first to support CXL 3.1 and PCIe Gen 6
SEMI: Global silicon wafer shipment area increased by 6.8% year-on-year and 5.9% month-on-month in 2024Q3
TSMC's 5nm and 3nm supply reaches "100% utilization" showing its dominance in the market
LG Display successfully develops world's first stretchable display that can be expanded by 50%
Seizing the Opportunities in the Chinese Application Market: NI's Challenges and Answers
New diaphragm-free solid-state lithium battery technology is launched: the distance between the positive and negative electrodes is less than 0.000001 meters
Photoresist giant JSR Korea EUV MOR photoresist production base started construction, expected to be put into production in 2026

New Posts

Featured

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

User Search：

Room 1530, Zhongguancun MOOC Times Building, Block B, 18 Zhongguancun Street, Haidian District, Beijing 100190, China Tel:(010)82350740 Postcode：100190

京公网安备 11010802033920号

快速回复返回顶部 Return list

ZYNQ cannot be burned to NAND Flash via JTAG [Copy link]

Latest reply

Comments

Comments

Visited sections