Training

Location:Training / Tools/EDA / Cadence Allegro 17.4 Getting Started with 66 PCB Layout Design Practical Videos / Introduction to Gerber file cascading and parameter settings

You can log in to your eeworld account to continue watching：
Introduction to Gerber file cascading and parameter settings
Login

Duration：36 minutes and 54 seconds
Date：2023/10/01

Uploader：Lemontree

Introduction

keywords： PCB Cadence

In order to solve the problems reported by students that Allegro is difficult to operate, cannot use the new version, do not know where to start learning this tool, and cannot install it, we used the latest version of CadenceAllegro17.4 to record this course. List some commonly used operations of the software from the following directions: schematic symbols, schematic drawing, PCB packaging, and PCB drawing. Each operation will be explained in a hands-on manner, and important knowledge points will be explained. The PPT list allows every student to quickly master and apply it to high-speed PCB design practice.

Learning objectives:
1. Master the use of Orcad tools to draw schematic symbols
2. Master the use of Orcad tools to draw schematic diagrams
3. Master the use of Allegro tools to draw PCB packages
4. Master the use of Allegro tools for PCB layout and wiring
5. Master the use of Allegro tools for impedance , Rule design
6. Master the use of Allegro tools to output production gerber files

You Might Like

Recommended Posts

DIY a No. 7 battery to light up a super bright LED for emergency use in power outages: 1. Circuit Schematic Preparation The voltage of a nickel-metal hydride battery is only 1.2V, while the ultra-bright LED requires a working voltage of more than 3.3V to ensure sufficient brightness. Th; qwqwqw2088 DIY/Open Source Hardware

Please tell me the definition of uint16: In the following definitionstruct HISPCP_BITS { // bits descriptionUint16 HSPCLK:3; // 2:0 Rate relative to SYSCLKOUTUint16 rsvd1:13; // 15:3 reserved};Why is there a colon in HSPCLK:3 after the uint1; 2002xiao DSP and ARM Processors

The story of DSP and parallel DA...: How should DSP be connected to parallel DA to output the processed data? The DSP of 5509A uses 8-bit parallel AD at the input end (occupying CE0 space and D0-D7 of DSP data line). How should the data; zhaironghui DSP and ARM Processors

[Routine experience of Flathead RVB2601 development board] Part 1: Download the example program successfully, sharing experience!: 1. Introduction I had just received the board and set up the development environment, but was stuck at the step of downloading the program. I felt that there were some problems when installing the dev; w494143467 XuanTie RISC-V Activity Zone

Transformer knowledge: [U][ip]A transformer is a device that transforms AC voltage, current and impedance. When AC current flows through the primary coil, AC magnetic flux is generated in the iron core (or magnetic core), c; fighting Analog electronics

I encountered an error when compiling PB. Can anyone help me? Thank you!: I am a novice. When I use wince5.0 to compile a new PB, the following error is prompted: making: FATAL ERROR:Cannot open F:\创建文件夹\2222\Reldir\smdk2440a_ARMV4I_Relea\postproc\platform.bib making: FATAL; chokee Embedded System

Recommended Content

Hot VideosMore

Hot ArticlesMore

Circuit

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函

京公网安备 11010802033920号