Cadence Allegro 17.4 Getting Started with 66 PCB Layout Design Practical Videos

In order to solve the problems reported by students that Allegro is difficult to operate, cannot use the new version, do not know where to start learning this tool, and cannot install it, we used the latest version of CadenceAllegro17.4 to record this course. List some commonly used operations of the software from the following directions: schematic symbols, schematic drawing, PCB packaging, and PCB drawing. Each operation will be explained in a hands-on manner, and important knowledge points will be explained. The PPT list allows every student to quickly master and apply it to high-speed PCB design practice.

Learning objectives:
1. Master the use of Orcad tools to draw schematic symbols
2. Master the use of Orcad tools to draw schematic diagrams
3. Master the use of Allegro tools to draw PCB packages
4. Master the use of Allegro tools for PCB layout and wiring
5. Master the use of Allegro tools for impedance , Rule design
6. Master the use of Allegro tools to output production gerber files

• Chapter 1：Course Introduction (16 minutes and 37 seconds)

• Chapter 2：Installation of Cadence Allegro version 17.4 (26 minutes and 11 seconds)

• Chapter 3：Introduction to Capture software operation interface and common settings (20 minutes and 57 seconds)

• Chapter 4：Introduction to the component library that comes with Capture software (10 minutes and 0 seconds)

• Chapter 5：Capture software creates component library (STM32 as an example) (29 minutes and 33 seconds)

• Chapter 6：Management and calling of Capture software component library (14 minutes and 7 seconds)

• Chapter 7：Introduction to the relationship between component library and PCB packaging library (9 minutes and 52 seconds)

• Chapter 8：Introduction to creating and adding commands to the Capture software schematic diagram (13 minutes and 4 seconds)

• Chapter 9：Capture software schematic diagram to add components (12 minutes and 58 seconds)

• Chapter 10：Capture software schematic diagram signal connection (14 minutes and 17 seconds)

• Chapter 11：Capture software schematic diagram power supply and ground connection (8 minutes and 46 seconds)

• Chapter 12：Capture software schematic diagram adds Bus bus (9 minutes and 53 seconds)

• Chapter 13：Capture software schematic diagram adds differential attributes (9 minutes and 8 seconds)

• Chapter 14：Capture software schematic PCB Footprint processing (6 minutes and 16 seconds)

• Chapter 15：Introduction to Capture software schematic DRC inspection tool (24 minutes and 41 seconds)

• Chapter 16：Capture software schematic PDF and BOM list output (12 minutes and 45 seconds)

• Chapter 17：Introduction to Capture software schematic diagram output of various PCB netlists (8 minutes and 44 seconds)

• Chapter 18：Analysis of common errors in Capture software schematic output netlist (24 minutes and 54 seconds)

• Chapter 19：Padstack Editor tool introduction (13 minutes and 41 seconds)

• Chapter 20：Introduction to the components of the PCB packaging library (9 minutes and 52 seconds)

• Chapter 21：PCB Editor software creates patch packages (STM32 as an example) (38 minutes and 42 seconds)

• Chapter 22：PCB Editor software creates plug-in packages (pins as an example) (32 minutes and 49 seconds)

• Chapter 23：Introduction to PCB Editor software wizard for creating packages (BGA as an example) (13 minutes and 35 seconds)

• Chapter 24：PCB Editor software 3D packaging display (10 minutes and 50 seconds)

• Chapter 25：Management and calling of PCB packaging library (15 minutes and 53 seconds)

• Chapter 26：Introduction to switching between Chinese and English in PCB Editor software (7 minutes and 12 seconds)

• Chapter 27：PCB Editor software operation interface and common settings introduction (14 minutes and 53 seconds)

• Chapter 28：PCB Editor software shortcut keys and Stroks command introduction (27 minutes and 42 seconds)

• Chapter 29：Capture and PCB Editor synchronize netlist and error analysis (28 minutes and 49 seconds)

• Chapter 30：PCB Editor background placement component analysis (6 minutes and 37 seconds)

• Chapter 31：PCB Editor manually adds components and network modifications (9 minutes and 37 seconds)

• Chapter 32：DXF file import and PCB board frame definition (20 minutes and 39 seconds)

• Chapter 33：PCB Editor software precise positioning and coordinate positioning (11 minutes and 57 seconds)

• Chapter 34：Schematic block diagram, power supply binary tree analysis (8 minutes and 49 seconds)

• Chapter 35：Capture and PCB Editor interactive layout and modularization (13 minutes and 5 seconds)

• Chapter 36：Conventional processing methods of network flying lines in PCB Editor software (9 minutes and 54 seconds)

• Chapter 37：Introduction to PCB Editor software Class and Sub-Class (41 minutes and 9 seconds)

• Chapter 38：Introduction to device movement, rotation, mirroring, alignment, and equal spacing operations (27 minutes and 46 seconds)

• Chapter 39：Introduction to device, network, via locking and unlocking operations (8 minutes and 40 seconds)

• Chapter 40：Introduction to reuse of the same modules in PCB Editor software (13 minutes and 5 seconds)

• Chapter 41：Introduction to PCB Editor software measurement and query operations (15 minutes and 11 seconds)

• Chapter 42：PCB routing stackup and impedance design (30 minutes and 24 seconds)

• Chapter 43：Adding and setting PCB routing vias (20 minutes and 33 seconds)

• Chapter 44：PCB Editor software differential pair addition and settings (9 minutes and 48 seconds)

• Chapter 45：Introduction and addition of PCB routing and spacing rules (34 minutes and 19 seconds)

• Chapter 46：PCB wiring class addition and color assignment (27 minutes and 25 seconds)

• Chapter 47：Introduction and addition of PCB wiring area rules (16 minutes and 37 seconds)

• Chapter 48：Introduction to PCB Editor software wiring and line repair operations (29 minutes and 25 seconds)

• Chapter 49：Introduction to copy, change and delete operations of PCB Editor software (23 minutes and 56 seconds)

• Chapter 50：PCB Editor software Z-Copy operation introduction (11 minutes and 43 seconds)

• Chapter 51：PCB Editor software Sub-Drawing operation introduction (16 minutes and 35 seconds)

• Chapter 52：Introduction to operations related to copper foil in PCB Editor software (51 minutes and 25 seconds)

• Chapter 53：Introduction to PCB Editor software fan-out related operations (29 minutes and 3 seconds)

• Chapter 54：Adding and setting snake-shaped equal-length rules in PCB Editor software (1 hours and 6 minutes and 26 seconds)

• Chapter 55：PCB wiring status inspection and related DRC model setting and elimination (10 minutes and 4 seconds)

• Chapter 56：Introduction to operations related to PCB Editor software annotation (11 minutes and 44 seconds)

• Chapter 57：Introduction to PCB file silk screen adjustment and related character processing (5 minutes and 40 seconds)

• Chapter 58：Preparation of relevant documents for MARK points, process edges, and impedance descriptions (21 minutes and 12 seconds)

• Chapter 59：Introduction to Gerber file cascading and parameter settings (36 minutes and 54 seconds)

• Chapter 60：Introduction to extracting Gerber hole symbols, drilling tables and drilling files (10 minutes and 35 seconds)

• Chapter 61：Introduction to Gerber file output (5 minutes and 4 seconds)

• Chapter 62：Introduction to IPC netlist, coordinate file, and assembly PDF output (9 minutes and 41 seconds)

• Chapter 63：Introduction to file packaging and file archiving (5 minutes and 43 seconds)

• Chapter 64：Introduction to Skill software’s one-click output of Gerber files (9 minutes and 18 seconds)

• Chapter 65：Introduction to Gerber file inspection using CAM350 tool (8 minutes and 16 seconds)

• Chapter 66：Practical introduction to PCB design for 2-layer and 4-layer projects (8 minutes and 5 seconds)