Training

Location:Training / Tools/EDA / Cadence Allegro 17.4 Getting Started with 66 PCB Layout Design Practical Videos / Introduction to IPC netlist, coordinate file, and assembly PDF output

You can log in to your eeworld account to continue watching：
Introduction to IPC netlist, coordinate file, and assembly PDF output
Login

Duration：9 minutes and 41 seconds
Date：2023/10/01

Uploader：Lemontree

Introduction

keywords： PCB Cadence

In order to solve the problems reported by students that Allegro is difficult to operate, cannot use the new version, do not know where to start learning this tool, and cannot install it, we used the latest version of CadenceAllegro17.4 to record this course. List some commonly used operations of the software from the following directions: schematic symbols, schematic drawing, PCB packaging, and PCB drawing. Each operation will be explained in a hands-on manner, and important knowledge points will be explained. The PPT list allows every student to quickly master and apply it to high-speed PCB design practice.

Learning objectives:
1. Master the use of Orcad tools to draw schematic symbols
2. Master the use of Orcad tools to draw schematic diagrams
3. Master the use of Allegro tools to draw PCB packages
4. Master the use of Allegro tools for PCB layout and wiring
5. Master the use of Allegro tools for impedance , Rule design
6. Master the use of Allegro tools to output production gerber files

You Might Like

Recommended Posts

Fujitsu FRAM Experience Submission: The sample model I applied for is MB85RC256V. I haven't used it yet, but I want to know the performance of this chip from the principle. There is nothing much to say about the power supply. It has a w; littleshrimp Integrated technical exchanges

Maintenance issues of soldering iron: [i=s]This post was last edited by paulhyde on 2014-9-15 09:35[/i] I would like to ask you: After using the soldering iron for a period of time, the temperature of the soldering iron tip cannot reach t; gina Electronics Design Contest

VxWorks interface and POSIX interface in VxWorks: I just started learning VxWorks, and there is a question that has always confused me when reading the documentation. The documentation says that VxWorks defines both VxWorks interfaces and you can als; se7enmoon Real-time operating system RTOS

The linear regulators or switching regulators we use generally have a maximum current limit. What does this mean specifically?: [backcolor=rgb(222, 240, 251)]The linear regulators or switching regulators we use generally have a maximum current limit. What does this mean specifically? Does it mean that if the current exceeds th; 乐君羊 Analogue and Mixed Signal

Why does the DC signal change so much before and after driving the LD after passing through the bias Tee circuit?: 50mA current drives LD, the output power of LD is 30uW. 50mA current drives LD through the bias Tee circuit, so the output power of LD should also be 30uW. Why does the power of LD increase 20 times a; szyang Analog electronics

Serial communication related: Please give me some advice, thanks. . I have three questions: 1. Now RS232 serial port usually uses 9-frame connection line. The simplest connection is 3 connection lines, namely ground connection (co; luoxianbo Embedded System

Recommended Content

Hot VideosMore

Hot ArticlesMore

Circuit

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函

京公网安备 11010802033920号