Analog signal isolation output circuit
The advantages of the analog signal isolation method are: only a small number of optocouplers are used, and the cost is low;
the disadvantage is that debugging is difficult. If the optocoupler is not selected appropriately, the accuracy and linearity of the conversion will be affected.
Previous article：A/D Converter Principle
Next article：Current output circuit of D/A converter
VLSI Design
Recommended Content
CMOS Analog Circuit Video Lecture Notes EECS240
3 days to get started with Persimmon UI, 2 days to finalize product interface development
DSP Technology (Lecturer of the University of Electronic Science and Technology of China’s Excellent Course: Peng Qicong)
Analysis and Design of a Flyback (flyback power supply design and analysis)
Loop Compensation of a Discontinuous Flyback
Latest Analog Electronics Articles
- High signal-to-noise ratio MEMS microphone drives artificial intelligence interactionAuthor: Dr. Gunar Lorenz Senior Director of Technology Marketing, Infineon Technologies Proofreader: Ding Yue Chief Engineer, Greater China, Consumer, Computing and Communications Business, Infineon Technologies Introduction At Infineon, I ...
- Advantages of using a differential-to-single-ended RF amplifier in a transmit signal chain designTraditional radio frequency (RF) transmit signal chains typically use a digital-to-analog converter (DAC) to generate a baseband signal. This signal is then up-converted to the desired RF frequency using an RF mixer and a local oscillator. ...
- ON Semiconductor CEO Appears at Munich Electronica Show and Launches Treo PlatformDuring Electronica, ON Semiconductor CEO Hassane El-Khoury was interviewed by Power Electronics News at the exhibition site and gave a detailed introduction to the new products that ON Semiconductor brought to the market. ...
- ON Semiconductor Launches Industry-Leading Analog and Mixed-Signal PlatformThe Treo platform uses a modular architecture that accelerates the development of intelligent power management, sensor interface and communication solutions. The Treo platform is based on 65-nanometer BCD process technology and supports ...
- Analog Devices ADAQ7767-1 μModule DAQ Solution for Rapid Development of Precision Data Acquisition Systems Now Available at MouserMouser Now Stocking Analog Devices ADAQ7767-1 μModule DAQ Solution for Rapid Development of Precision Data Acquisition Systems November 6, 2024 – Offering a broad range of semiconductor and electronics ...
- Domestic high-precision, high-speed ADC chips are on the rise
- Microcontrollers that combine Hi-Fi, intelligence and USB multi-channel features – ushering in a new era of digital audio
- Using capacitive PGA, Naxin Micro launches high-precision multi-channel 24/16-bit Δ-Σ ADC
- Fully Differential Amplifier Provides High Voltage, Low Noise Signals for Precision Data Acquisition Signal Chain
MoreSelected Circuit Diagrams
MorePopular Articles
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
MoreDaily News
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
Guess you like
- Battery Pack BMS Coulomb Counter Chip Solution
- How to distinguish between pads and vias_Differences between vias and pads
- Could you please tell me what circuit is generally used to implement the 0/4-20mA drive circuit?
- Principle and application of diaphragm pressure gauge
- Showing off your products (6) - silicon lab
- EEWORLD University - How to draw a high-end PCB ruler with Altium20
- Agitek case sharing - Metrology and testing demonstration case of automotive electronic modules
- How to turn off MPLAB XIDE's code optimization function
- IoT Smart Parking Solutions
- EPWM1 A and B pulses are not complementary
京公网安备 11010802033920号