Today I will share with you a novel solar LED light controller circuit diagram. The main function of this solar LED light controller is to use solar panels to charge the battery during the day, and use two-stage lighting at night, that is, it lights up after dark and automatically turns off late at night, and automatically lights up before dawn the next day, and automatically turns off after dawn. As shown in the figure below.
Previous article:[Graphical Analysis] How much electricity can LED lights save compared to traditional lamps!
Next article:LED power drive circuit diagram
- MathWorks and NXP Collaborate to Launch Model-Based Design Toolbox for Battery Management Systems
- STMicroelectronics' advanced galvanically isolated gate driver STGAP3S provides flexible protection for IGBTs and SiC MOSFETs
- New diaphragm-free solid-state lithium battery technology is launched: the distance between the positive and negative electrodes is less than 0.000001 meters
- [“Source” Observe the Autumn Series] Application and testing of the next generation of semiconductor gallium oxide device photodetectors
- 采用自主设计封装,绝缘电阻显著提高!ROHM开发出更高电压xEV系统的SiC肖特基势垒二极管
- Will GaN replace SiC? PI's disruptive 1700V InnoMux2 is here to demonstrate
- From Isolation to the Third and a Half Generation: Understanding Naxinwei's Gate Driver IC in One Article
- The appeal of 48 V technology: importance, benefits and key factors in system-level applications
- Important breakthrough in recycling of used lithium-ion batteries
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
- VS1053b cannot play music
- HyperLynx High-Speed Circuit Design and Simulation (VIII) High-Speed Board-Level Simulation
- I would like to ask, for NPN tube, does the leakage current ICEO refer to the flow from C to E or from E to C?
- EE Mobile Station Development Board Introduction: DA14580DEVKT-B Evaluation Board
- No doubt! Real-time measurement can also be done with low power consumption
- Read the good book "Electronic Engineer Self-study Handbook" + Advanced Edition
- 【Based on Gizwits AIoT development platform + Gokit】+ X-ray dose monitor
- Providing a 1.5V reference voltage to a thermocouple can expand the entire measurement temperature range? What is the principle?
- See the circuit and eat the circuit to verify the circuit
- How to multithread?