Socket installation position rules:
1. Generally, the bottom edge of the socket should be 0.3 meters from the ground and installed at the same height, with a difference of no more than 5mm;
2. On each wall of the living room and bedroom, the distance between two sockets should not be higher than 2.5 meters, and at least one spare socket should be installed within 0.6 meters of the corner;
3. The socket of the washing machine should be between 1.2m and 1.5m from the ground. It is best to choose a three-pole socket with a switch;
4. The refrigerator socket should be 0.3m or 1.5m from the ground (depending on the location of the refrigerator), and a single three-pole socket should be selected;
5. The sockets of split-type and wall-mounted air conditioners should be set 1.8 meters from the ground according to the reserved hole of the outlet pipe. The sockets of window-type air conditioners can be set 1.4 meters from the ground next to the window. The power sockets of cabinet air conditioners should be set 0.3 meters from the ground at the corresponding position.
6. The range hood socket should be installed at a height of 1.8 to 2 meters from the ground according to the design of the kitchen cabinet, and it is best to be covered by the exhaust pipe;
7. The socket of the electric water heater should be installed on the right side of the water heater, 1.4m to 1.5m from the ground. Be careful not to install the socket above the electric heater;
8. The terrace socket should be at least 1.4 meters from the ground and should be kept away from sunlight and rain as much as possible;
9. In the kitchen, bathroom, and terrace, the sockets should be installed as far away from the water-using area as possible. If they are close, a splash-proof box should be added. A power socket for a hair dryer and a shaving machine can be installed next to the basin mirror, preferably 1.5 to 1.6 meters above the ground;
10. Sockets shall not be installed near the stove.
Previous article:What are the components of a low voltage circuit breaker?
Next article:How to complete the reasonable design of switching power supply from conception to practice
- Popular Resources
- Popular amplifiers
- MathWorks and NXP Collaborate to Launch Model-Based Design Toolbox for Battery Management Systems
- STMicroelectronics' advanced galvanically isolated gate driver STGAP3S provides flexible protection for IGBTs and SiC MOSFETs
- New diaphragm-free solid-state lithium battery technology is launched: the distance between the positive and negative electrodes is less than 0.000001 meters
- [“Source” Observe the Autumn Series] Application and testing of the next generation of semiconductor gallium oxide device photodetectors
- 采用自主设计封装,绝缘电阻显著提高!ROHM开发出更高电压xEV系统的SiC肖特基势垒二极管
- Will GaN replace SiC? PI's disruptive 1700V InnoMux2 is here to demonstrate
- From Isolation to the Third and a Half Generation: Understanding Naxinwei's Gate Driver IC in One Article
- The appeal of 48 V technology: importance, benefits and key factors in system-level applications
- Important breakthrough in recycling of used lithium-ion batteries
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
- Detailed explanation of intelligent car body perception system
- How to solve the problem that the servo drive is not enabled
- Why does the servo drive not power on?
- What point should I connect to when the servo is turned on?
- How to turn on the internal enable of Panasonic servo drive?
- What is the rigidity setting of Panasonic servo drive?
- How to change the inertia ratio of Panasonic servo drive
- What is the inertia ratio of the servo motor?
- Is it better for the motor to have a large or small moment of inertia?
- What is the difference between low inertia and high inertia of servo motors?
- control
- 【CH579M-R1】+W25Q16 storage module reading and writing
- Is this the worst impedance processing you have ever encountered?
- PCB panelization
- RPG game ported using RP2040 and MicroPython
- For large project files containing nios, timing constraints, and layout and routing, modify the internal module names and some variable names.
- What is output impedance? What is impedance matching?
- High-frequency transformer sandwich winding method: primary wrapped in secondary? Or secondary wrapped in primary?
- Detailed description of I2C bus protocol and timing, getting started is no longer difficult
- LM1875 Op Amp