(2) If two American EC80 F/30V capacitors are connected in parallel, the measurement accuracy of the dynamic signal can be improved.
(3) It is best to use a digital multimeter as a DC voltmeter, which can greatly improve the resolution. At the same time, it is not necessary to frequently adjust the meter handle like a pointer multimeter.
(4) When measuring high-power tubes, it is recommended to connect a 2A fuse in series with the resistor for safety reasons.
Previous article:Methods for testing differential pair transistors
Next article:Design of power parameter measurement based on MAX274
Recommended ReadingLatest update time:2024-11-16 00:40
- Popular Resources
- Popular amplifiers
- Nursing home intelligent care system
- Evaluating Roadside Perception for Autonomous Vehicles: Insights from Field Testing
- Electrical and Electronic Technology (Editors-in-Chief: Liu Yaoyuan, Hu Minshan; Associate Editors-in-Chief: Zou Xiaolian, Zhou Hongyu, Li Heshui)
- Practical training guidance for new electrician technology (Wu Qihong, Jiang Jian, Xu Kungang, Zhang Hong)
- Keysight Technologies Helps Samsung Electronics Successfully Validate FiRa® 2.0 Safe Distance Measurement Test Case
- From probes to power supplies, Tektronix is leading the way in comprehensive innovation in power electronics testing
- Seizing the Opportunities in the Chinese Application Market: NI's Challenges and Answers
- Tektronix Launches Breakthrough Power Measurement Tools to Accelerate Innovation as Global Electrification Accelerates
- Not all oscilloscopes are created equal: Why ADCs and low noise floor matter
- Enable TekHSI high-speed interface function to accelerate the remote transmission of waveform data
- How to measure the quality of soft start thyristor
- How to use a multimeter to judge whether a soft starter is good or bad
- What are the advantages and disadvantages of non-contact temperature sensors?
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
- [GD32L233C-START Review] 2. Non-blocking way to light up, blink, blink, blink...
- MSP432P401M MSP432P4xx: Falcon Series
- [F-Wireless Microphone Amplification System] Hubei Province_First Prize
- [Repost] Nine things to note when testing PCB boards
- [Fudan Micro FM33LC046N Review] + GPTIM_PWM
- Automotive RFCMOS 77GHz Radar Module Design
- Help: Puyuan DS5102CA waveform measurement problem
- What is the difference between cmw500 signaling and non-signaling?
- MSP430 MCU Development Record (2)
- [MM32 eMiniBoard Review] + OLED screen driver display