Fitting data based on known data weights

Recommended ContentMore

Open source project More

• 【Core board】STM32F103C8T6
• smart car
• 1/8 brick power module based on ADP1051
• USB-HUB
• System-in-Package Evaluation Board with Integrated Microstepping Controller and 10 A Power MOSFET
• STR-PWRNCV330-R0-GEVK: Automotive Strata Controlled Load Switch with Soft-Start
• Laser engraving machine 2.02 v0.1
• 【Training Camp】Robotic Arm
• DER-613 - 27W USB PD 3.0 based on InnoSwitch3-Pro and Weltrend WT6635P controller (single board design) with 3.3 V-11 V PPS power supply
• Minimal system schematic diagram

Searched by Users

• Qt and Qt+Quick development practical analysis_2
• Danfoss VLT2900 inverter Chinese operation manual (MG29A341)
• Tornado2.2 for Arm Download
• Renesas MCU Download Software
• Protel 99SE Chinese character input patch
• Mastercam9.0 Download_Chinese Version
• Verilog-A/AMS System Design and Simulation [Wu Shunmin]
• Configurator circuit diagram design tool software (Lintech)
• Cortex M3 Definitive Guide (Chinese)
• Xunwei embedded development board iTOP-4412 development board Linux experiment manual

Just Take a LookMore

• 【Goodbye 2021, Hello 2022】+ It’s time to sum up the year again
  [i=s]This post was last edited by yanbao on 2022-1-9 17:56[/i]Today, 20220109, the seventh day of the twelfth lunar month. I still remember that when I reviewed 2021 last year, it was 20210204, the Li
• Triode lawn mower circuit
  The original intention of the person who drew this circuit was to be funny and inspirational. However, as far as the triode circuit is concerned, the artist is a weed waiting to be hoeed. I often see
• In the CNNE instruction, if (a) < (driet), then 1->cy, is this explanation correct?
  [i=s]This post was last edited by Yishayishi on 2022-8-16 12:01[/i]The CNNE instruction, as shown in the figure below, has the following explanation: If (a)(driet), then 1-cy. Is this explanation corr
• Share the common problems of MSP430: LCD display driver
  Q1: Crystals are usually connected to 32768, and it is normal to use LCD. I plan to connect the crystal to 6M to replace 32768, will the LCD still display normally?A1: See what the timing limit of the
• Network port with a speed of 5G or above
  What models support network ports with rates above 5G?
• The origin of the BUCK circuit, with three evolutionary circuits
• DSP Learning (1) Introduction to Digital Signal Processors (DSPs)
• 【Portable Environmental Status Detector】RTC Electronic Clock
• Espressif's ESP32-C3 is an extremely low-power SoC equipped with a RISC-V 32-bit single-core processor
• Why does the STACK MODE of almost all pads in ALTIUM DESIGNER change to FULL STACK?

Trending Downloads

• Changhong SF2539(F21)-CH05T1630-24C16A-BSC62A movement EPROM data
• Photoelectric Technology and Experiment (Beijing Institute of Technology Press, 2000)
• ARM7 lpc2468 reference circuit
• Temperature sensor modular programming
• Transformer Design Principles, edited by Yin Kening
• Design of DC motor speed measuring device - based on the 2017 National Undergraduate Electronic Design Competition Project
• RC523 reads Type B card.doc
• DSP functions implemented with MATLAB
• Peking University Digital Integrated Circuit Courseware--22_Verilog Writing Style
• MTK6228 complete schematic diagram[1].pdf

Trending ArticlesMore

• The CPU is "stuck". Can the new track domestic GPU be adopted?
• Charging Extra | Make life "wireless" possible
• Dialog Mobile TV SoC Products
• Competition report | 24-hour Hackathon challenge is in full swing!
• Samsung gives up acquisition? NXP CEO and CFO both reduce their holdings!
• 2015 Google I/O Conference: New generation of Chromebooks made in China revealed
• The US makes things difficult for Huawei, but Taiwan's semiconductor companies benefit
• Selection of the latest chip product technology content
• Breaking News | Infineon Technologies Announces Latest Investment Plan in China at the CIIE
• Analyst: China's semiconductor industry self-sufficiency process is accelerating