Figure 7. Standard PECL Output Configuration Figure 8. Single Resistor Termination Scheme
Resistor values are typically 140 ohms for
3.3V operation.
Resistor values are typically 84 ohms for 2.5V
operation.
The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 7. There are numerous application notes on
terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 8, and a pull-up/pull-down scheme as
shown in Figure 9. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
LVDS Application Diagrams
V
CC
LVDS
Driver
100
LVDS
Receiver
LVDS
Driver
100
Receiver
OUT+
OUT-
Figure 10 Standard LVDS
Output Configuration
Figure 11. LVDS to LVDS Connection, Internal 100ohm
Figure 12. LVDS to LVDS Connection
Some LVDS structures have an internal 100 ohm resistor on the
External 100ohm and AC blocking caps
input and do not need additional components.
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
Ultrasonic transmitter and receiver split ruler (GPS/BDS chip PPS signal is used as time synchronization, the synchronization error is about ten microseconds)
This is a self-made project that I have p...
Today, MicroPython officially released the pyb D series development board and started selling it in the official store. The matching baseboard and expansion board are also on sale. The new pyb D serie...
Regarding the directional positioning of Bluetooth 5.1, I have looked online and found that there are basically no in-depth articles. Most of them are just superficial introductions. I feel that this ...
Original article by Mr. High Speed | Huang GangIf you are asked to evaluate the crosstalk of high-speed serial signals, you will say that their crosstalk is below -40db and has no effect. But if you a...
I used ap4 to generate code, and then created a new project with cs+ for ca. After adding the c file, I set the device configuration in Link Options according to the content in the r_option_ca.txt fil...
1. The default level of the MCU IO port is high after power-on. (P1, P2, and P3 ports are internally pulled up. If the P0 port is not connected to a pull-up resistor, the default is high impedance....[Details]
In response to the national mourning event on April 4, 2020 announced by the State Council, the OPPO ColorOS official community issued an announcement today stating that from 00:00 on April 4, th...[Details]
The increasing number of electrical loads in today's cars poses challenges to the battery. More than half of all vehicle faults caused by the electrical system can be attributed to the lead-acid ba...[Details]
If the development of the integrated circuit industry is sorted out vertically and horizontally, then in the vertical direction, the evolution of process nodes represented by Moore's Law will be a re...[Details]
With MSP430 processor as the core, combined with photoelectric micro-loss blood glucose monitoring technology, and using three-probe fiber bundle sensor, a new blood glucose monitoring system is de...[Details]
element14, a global distributor of electronic components and development services, has announced the launch of its latest design challenge through its online community (one of Avnet's communities), e...[Details]
1 Introduction to Electric Vehicles and Range Extenders
Electric vehicles refer to vehicles that use electric motors as their power system in whole or in part. They include three types...[Details]
TGC is a home intelligent TV program recording system. Its Chinese name is "record for you". Through TIVO's unique intelligent TV entertainment platform, you can watch TV more efficiently, get rid of...[Details]
MMU is a memory management unit, which is responsible for mapping virtual addresses to physical addresses and checking memory access permissions. This article only talks about address mapping. The ad...[Details]
introduction An inverter is an electrical device that converts steam power into AC power, usually implemented with high-power and high-reverse voltage power electronic devices. In solar power...[Details]
It plays a key role in various industries, improving production efficiency, reducing costs, improving quality, and even changing the production methods of the entire industry. So, what are the comp...[Details]
introduction
In recent years, the construction of municipal solid waste incineration power plants has developed rapidly in my country. As one of the ways to clean waste treatment, waste incine...[Details]
Recently, Lihong Qin, co-founder and president of NIO, revealed at a 100kWh battery sharing session that at the NIO Day event held on January 9, 2021, NIO will release its first sedan, 150kWh battery...[Details]
The recent " triple play
"
of telecommunications, broadcasting and the Internet proposed by the State Council of China
has brought new market opportunities to network operators and re...[Details]
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
