LCGGX1T10EWUE datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> switch> LCGGX1T10EWUE

LCGGX1T10EWUE: DescriptionSNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 1A, 30VDC, 4.3mm, PANEL MOUNT, ROHS COMPLIANT; CategoryMechanical and electronic products switch; File Size198KB，4 Pages; ManufacturerC&K; Environmental Compliance

Download Datasheet Parametric View All

LCGGX1T10EWUE Overview

SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 1A, 30VDC, 4.3mm, PANEL MOUNT, ROHS COMPLIANT

LCGGX1T10EWUE Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	C&K
package instruction	ROHS COMPLIANT
Reach Compliance Code	compliant
ECCN code	EAR99
Actuator stroke	4.3 mm
Actuator type	LEVER, HIGH FORCE
body width	6.1 mm
body height	9.32 mm
Body length or diameter	19.84 mm
Contact (AC) maximum rated R load	1A@125VAC
Maximum contact current (AC)	1 A
Maximum contact current (DC)	1 A
Contact (DC) maximum rated R load	1A@30VDC
Maximum contact voltage (AC)	125 V
Maximum contact voltage (DC)	30 V
Electrical life	100000 Cycle(s)
Installation features	PANEL MOUNT
Maximum operating force	0.47 N
Maximum operating temperature	85 °C
Minimum operating temperature	-25 °C
Maximum pre-travel	3.56 mm
seal	EPOXY TERMINAL SEALED
surface mount	NO
Switch action	MOMENTARY
switch function	SPST
Switch type	SNAP ACTING/LIMIT SWITCH
Termination type	SOLDER
Base Number Matches	1

Preview

Download Datasheet

View All

LC Series

Subminiature Precision Snap-acting Switches

Features/Benefits

•

Compact design

•

Long life and high electrical capacity

•

Quick connect, wire lead or PC mounting

•

Wide variety of actuator styles

Typical Applications

•

Motorized equipment

•

Sump pump

•

Thermostatic controls

Specifications

CONTACT RATING: From low level* to 10.1 AMPS @ 250 V AC.

ELECTRICAL LIFE: 100,000 cycles

INSULATION RESISTANCE: 1,000 M

οηµ

min.

DIELECTRIC STRENGTH: 1,000 Vrms min. @ sea level.

OPERATING TEMPERATURE: –17ºF to 185ºF (–25ºC to 85ºC).

OPERATING FORCE: From 142 to 170 grams at actuator button.

Forces are less at free end of lever actuators; (see OPERATING

FORCE and ACTUATOR option sections).

MOUNTING: 2-56 screws, torque 2.3 in/lbs max.

* Low Level=conditions where no arcing occurs during switching, i.e., 0.4 VA max. @

20 V AC or DC max.

NOTE:

Specifications and materials listed above are for switches with standard options.

For information on specific and custom switches, consult Customer Service center.

Materials

SWITCH HOUSING: Thermoplastic polyester or high temperature

thermoplastic (PTS) (UL 94V-0).

ACTUATOR BUTTON: Thermoplastic polyester (UL 94V-0).

SPRING: Copper alloy.

PIVOT: Copper alloy.

MOVABLE CONTACTS: Fine silver for ratings greater than 1 AMP

@ 125 V AC. Fine silver with 24K gold plate for 1 AMP @

125 V AC or less.

STATIONARY CONTACTS: Fine silver welded on copper alloy for

ratings greater than 1 AMP @ 125 V AC. Gold alloy welded

on copper alloy for ratings less than 1 AMP @ 125 V AC.

TERMINALS: Copper alloy.

TERMINAL SEAL: Epoxy.

Snap-acting

Build-A-Switch

To order, simply select desired option from each category and place in the appropriate box. Available options are shown and

described on pages J-18 through J-20. For additional options not shown in catalog, consult Customer Service Center.

Series

SP, Mom.

Operating Force

5 oz./142 grams

3.3 oz./94 grams

6 oz./170 grams

Electrical Rating

1 A, 125, V AC, 30 V DC

5 A, 1/3 HP, 125, 250 V AC

10.1 A, 1/3 HP, 125, 25O V AC

5 A, 1/3 HP, 125, 250 V AC

1 A, 125 V AC, 3O V DC

Actuator

P00

Pin plunger

A10

.28" lever roller, high force

A25

.61" lever roller, low force

T10

.29" lever, high force

T13

.22" simulated roller, high force

T20

.38" lever, low force

T23

.32" simulated roller, low force

T25

.67" lever, low force

Terminations

Solder

.110" quick connect

Wire lead

Left formed PC thru-hole

Right formed PC thru-hole

PC Thru-hole

Circuitry

SPDT

SPST N.C.

SPST N.O.

Electrical Life

NONE

6,000 operations

Extended 100,000 operations

Seal

NONE

(STD.) No seal

Epoxy seal

Dimensions are shown: Inches (mm)

Specifications and dimensions subject to change

J–17

www.ck-components.com

Recommended Resources

High frequency crystal oscillator circuit diagram

SS0622 touch step dimming light circuit

Loop timing circuit

6V nickel-cadmium battery charger circuit

TDA8170-72 power amplifier circuit

Amplification circuit reference

[RISC-V MCU CH32V103 Review] + ADC analog watchdog: When we use ADC, we sometimes need to monitor the ADC value within a certain range. Traditional polling processing is often not timely enough. Adding two voltage comparators to the periphery increases...; eew_Violet Domestic Chip Exchange

I2C Range Extension Reference Design: I2C to CAN: This design focuses on using a CAN transceiver to extend the I2C range from on-board to off-board through a transmission cable and then convert the signal back to I2C. This approach helps improve sign...; fish001 Microcontroller MCU

CC1352P1 LaunchPad communication distance test: CC1352P is a multi-band wireless MCU with integrated PA. The maximum transmit power at SUB-1G can reach 20dBm. This is why the CC1352P LaunchPad is $10 more expensive than the CC1352R LaunchPad withou...; littleshrimp Wireless Connectivity

Application of Aigtek power amplifier in performance study of electrokinetic migration-capture-release of Pb-contaminated municipal sludge: Experiment name: Application of power amplifier in electrolysis device of sludge electric remediation technology Purpose: The one-step method removes and recovers Pb from urban sludge, striving to ach...; aigtek01 Test/Measurement

Recently, the project department has taken on a new project, which requires the performance indicators of IC to meet industrial requirements. Can someone recommend...: Recently, the project department has taken on a new project that requires the performance indicators of the IC to meet industrial-grade requirements. Does anyone have any recommendations?...; wangjpq Security Electronics

I would like to ask for advice from all the experts. How can a fully enclosed metal shell increase the signal strength of NB?: We are currently making a set of outdoor smart locks, which are anti-theft and have no obvious prying points. This means that it is a fully enclosed shell, which is also installed on a metal cabinet. ...; cheery60 RF/Wirelessly

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components