ghaytweyhtoo

【Training Camp】【Training Camp】Bionic Tank

Overview

Introduction: Use hi3861 to create a four-legged robot creature. Product introduction: It is developed based on the OpenHarmony open source Hongmeng system. The chip used is hi3861. It supports up to 16 channels of servo control, GPIO, ADC, PWM and other operations. It can realize forward, backward, standing still, squatting and other operation application scenarios. : Can control robot dogs, small spiders, and other quadrupeds. Biochip solution: Multi-channel servo control board based on HiSilicon Hi3861 chip and PCA9685 Product core parameters: Power supply: 1 18650 battery Battery output: Charged by boosting to 8VDC : 1mA battery management charging chip hardware interface: gpio, ADC, PWM double-layer board design single-sided layout

Design Files

Related Devices

Devices	Class	introduce	Datasheet
TM8M475K010UBA	Tantalum capacitor		Download
FXL0630-4R7-M	Passive components;Power inductor	Accuracy: ±20% Rated current: 6A DC resistance (internal resistance): 33mΩ Inductance value: 4.7uH One-piece inductor alloy inductor super large inductor power inductor	Download
0603WAF1102T5E	Passive components;SMD resistor	Resistance (ohms): 11K Accuracy: ±1% Power: 1/10W Temperature coefficient: ±100ppm/°C	Download
0603WAF1543T5E	Passive components;SMD resistor	Resistance (ohms): 154K Accuracy: ±1% Power: 1/10W Temperature coefficient: ±100ppm/°C	Download
RC0603FR-071KL	Passive components;The resistor	Resistance (ohms): 1K Accuracy: ±1% Power: 1/10W Temperature coefficient: ±100ppm/°C	Download
1206W4F3301T5E	Passive components;SMD resistor	Resistance (ohms): 3.3K Accuracy: ±1% Power: 1/4W Temperature coefficient: ±100ppm/°C	Download
500	Power management;The battery compartment/battery holder		Download
ITCAST-HI3861	WIFI module		Download
AMS1117-3.3	Power/power management;Low dropout linear regulator (they)	Output type: Fixed Maximum input voltage: 18V Output current: 1A Output voltage (minimum/fixed): 3.235V	Download

All reference designs on this site are sourced from major semiconductor manufacturers or collected online for learning and research. The copyright belongs to the semiconductor manufacturer or the original author. If you believe that the reference design of this site infringes upon your relevant rights and interests, please send us a rights notice. As a neutral platform service provider, we will take measures to delete the relevant content in accordance with relevant laws after receiving the relevant notice from the rights holder. Please send relevant notifications to email: bbs_service@eeworld.com.cn.

It is your responsibility to test the circuit yourself and determine its suitability for you. EEWorld will not be liable for direct, indirect, special, incidental, consequential or punitive damages arising from any cause or anything connected to any reference design used.

Hot

Technical Resources More

Search Datasheet?

Supported by EEWorld Datasheet

Technical Videos More

Forum More

Update:2024-11-21 19:19:20

What is the chip with 4BMN silk screen? It has 5 pins.
I searched all over the Internet, but couldn't find the specific model of this chip. Could anyone tell me if anyone knows the model of this chip? Thank you.
Can I ask the experts, can a sine wave be converted into a square wave only by using an adder?
I think it is impossible to achieve this. Can't the only way to convert a sine wave into a square wave be to use a comparator? Please give me some advice.
Next-generation DOCSIS 4.0 products, CATV amplifiers based on gallium nitride (GaN) technology
The advent of DOCSIS 3.1 has enabled CATV providers to increase both upstream and downstream capacity. The next generation of DOCSIS 4.0 products is currently in the design phase. Using the right CATV
Schematic Design
In the schematic diagram, the FD2 signal passes through P2 of D16 and DAN217, and then passes through P1 of D16. Will the P2 line of D16 in the middle short-circuit P1 of D16 above? I am a novice, ple
Bluetooth Protocol
I was also looking for Bluetooth protocols some time ago. I found some of them, but they seemed very difficult and I slowly digested them.
I encountered a problem when testing the CAN communication isolation chip a few days ago. I hope you can give me some advice.
The question is quite long, so I wrote it in the Word attachment, and also attached the chip specification. I think it might be caused by the incorrect input level range of CAN communication.

Datasheet More

Circuits More