• You can log in to your eeworld account to continue watching:
  • Audio_FFT
  • Login
  • Duration:1 hours and 4 minutes and 34 seconds
  • Date:2018/08/23
  • Uploader:老白菜
Introduction
keywords: Linux Xilinx zq

This tutorial explains the basics of FPGA, introduction to SOC, DMA and VDMA, linux, HLS images and PCIE

Suitable for the following applications:

High-speed communications; machine vision, robots; servo systems, motion control; video collection, video output, consumer electronics; early stage verification of project research and development; learning for developers in electronic information engineering, automation, communication engineering and other electronic related majors

Unfold ↓

You Might Like

Recommended Posts

How to learn to make a single chip microcomputer system
I learned STM32 by reading the data manual before, but I felt that I only learned about software programming. Now my tutor wants me to make a complete system by myself, that is, I need to add power su
小赖同学 stm32/stm8
e-core electronic technology exchange group 4 starts using 35871678!
[i=s] This post was last edited by paulhyde on 2014-9-15 09:25 [/i] e-core electronic technology exchange group 4 has started using 35871678! Thank you for your support
liufeng2_0 Electronics Design Contest
DIY a ESP32 game console based on MicroPython
From https://www.hackster.io/alankrantas/diy ... p32-413d9eThe microcontroller used is WeMos D1 mini ESP32, which uses ESP32-WROOM.Display is 128x96 0.96 inch SSD1306 OLEDreference programfrom machine
dcexpert MicroPython Open Source section
Question about shield resistance...
I recently saw a circuit that connected four shielding resistors to the four lines of the touch screen and pulled them down to ground. I would like to ask: 1. Why do the four lines of the touch screen
wanglicha Embedded System
The microcontroller cannot receive data sent by the PC
#include "msp430x54x.h" void main(void){ WDTCTL = WDTPW + WDTHOLD; // Stop WDT P5SEL |=BIT6+BIT7; //USCI_A1 TXD/RXD P5DIR |=BIT5+BIT6; P5OUT =~BIT5;UCA1CTL1 |= UCSWRST; // **Put state machine in reset
zzbaizhi Microcontroller MCU
STMF103ZET6 uses the nucleo library
Modified from nucleo-F103RB library, if there are any errors, please point them out. . .
水清波 stm32/stm8

推荐文章

Linux内核分析:uboot与Linux内核机器码分析 2025年01月16日
1. uboot机器码 在uboot启动的start_armboot阶段,调用board_init函数初始化机器码。 int board_init(void) { .............................. gd- bd- bi_arch_number = MACH_TYPE_SMDKV210; gd- bd- bi_boot_params...
Linux内核的中断机制 2025年01月16日
1. 中断简介 中断是指在CPU正常运行期间,由于内外部事件或由程序预先安排的事件引起的CPU暂时停止正在运行的程序,转而为该内部或外部事件或预先安排的事件服务的程序中去,服务完毕后再返回去继续运行被暂时中断的程序。Linux中通常分为外部中断(又叫硬件中断)和内部中断(又叫异常)。 2. Linux内核中断机制的初始化 2.1 相关数据结构 linux内核将所有的中断统...
Linux内核静态映射表的建立过程 2025年01月16日
/* * 平台: s5pv210 * 内核版本号: 2.6.35.7 */ kernel/arch/arm/mach-s5pv210/mach-smdkc110.c 这个文件是由三星在移植内核时提供的一个很重要的文件,这个文件中的函数都是与硬件相关的。 mach-smdkc110.c文件中的smdkc110_map_io函数就是静态映射表建立过程调用的一个函数...
Linux驱动入门(七)使用定时器消除按键抖动 2025年01月16日
一、为什么要消抖? 二、如何消抖? 三、Linux内核定时器 四、源码 五、测试 本文将在Linux驱动入门(五)阻塞方式实现按键驱动的基础上,使用定时器消除按键抖动 一、为什么要消抖? 对于没有做硬件消抖的按键,在按下按键到电平稳定期间,会有一段抖动,此时电平会在高电平和低电平不断地跳动 如果我们的按键中断采用下降沿触发,从图中可以看出有多段下降沿,那么想必按下一次按键...

Recommended Content

Circuit

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews


Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号