After the ICF file and startup code are prepared, you can create a new IAR project and start the S3C6410 naked journey.
The environment for this step is IAR FOR ARM 6.10
1. Create a new project and select the kernel
2. Configure the header file path: project directory\inc
3. Add the icf file in the directory folder
4. For debugging, you can choose Simulator (software simulation) or J-Link/J-Trace (jlink simulator)
5. Add startup code
6. Click the simulation button, and you can see that the exception vector table is allocated at address 0x50000000
After that, you can start the naked journey of S3C6410~
Previous article：Notes on IAR debugging S3C6410 (Part 4)
Next article：Notes on IAR debugging S3C6410 (Part 1)
- Popular Resources
- Popular amplifiers
LF147D/883
- Download from the Internet--ARM Getting Started NotesA brief introduction: From today on, the ARM notebook of the rookie is open, and it can be regarded as a place to store these notes. Why publish it? Maybe you are interested in it. In fact, the reason for these notes is ...
- Learn ARM development(22)Turning off and on interrupts Interrupts are an efficient dialogue mechanism, but sometimes you don't want to interrupt the program while it is running. For example, when you are printing something, the program suddenly interrupts and another ...
- Learn ARM development(21)First, declare the task pointer, because it will be used later. Task pointer volatile TASK_TCB* volatile g_pCurrentTask = NULL;volatile TASK_TCB* vol ...
- Learn ARM development(20)With the previous Tick interrupt, the basic task switching conditions are ready. However, this "easterly" is also difficult to understand. Only through continuous practice can we understand it. ...
- Learn ARM development(19)After many days of hard work, I finally got the interrupt working. But in order to allow RTOS to use timer interrupts, what kind of interrupts can be implemented in S3C44B0? There are two methods in S3C44B0. ...
- Learn ARM development(14)
- Learn ARM development(15)
- Learn ARM development(16)
- Learn ARM development(17)
Professor at Beihang University, dedicated to promoting microcontrollers and embedded systems for over 20 years.
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
- Huawei's Strategic Department Director Gai Gang: The cumulative installed base of open source Euler operating system exceeds 10 million sets
- Download from the Internet--ARM Getting Started Notes
- Learn ARM development(22)
- Learn ARM development(21)
- Learn ARM development(20)
- Learn ARM development(19)
- Learn ARM development(14)
- Learn ARM development(15)
- Analysis of the application of several common contact parts in high-voltage connectors of new energy vehicles
- Wiring harness durability test and contact voltage drop test method
- [Smartwatch for environmental experts] Part 7: Dynamically add personnel and display data in real time
- Looking for related fields WeChat group
- TI C6000 Data Storage Processing and Performance Optimization
- Thermal Management of RF Power Devices
- The Sipeed LicheeRV 86 development board looks very tempting. Can I use it if I don’t know Linux?
- What level of accuracy and conversion rate have been achieved with domestic analog op amps?
- I published a PCB layout of an RF power amplifier in RF, but I don't know the materials.
- Wireless Radio Frequency Identification Technology-RFID Theory and Application
- ATmega4809 Curiosity Nano Review Lighting
- PCIE Standard.pdf
京公网安备 11010802033920号