STM8 IAR related notes-EEWORLD

Collect

If the .h file is not in the program root directory, you need to specify the location, as shown below:

STM8 IAR related notes

In this way, the compiler can find the location of the .h file without error. As for the .c file, you can add it directly, as shown in the figure below

STM8 IAR related notes

Keywords：STM8 Reference address：STM8 IAR related notes

Previous article：STM8S study notes 4 (STM8 time1)
Next article：IAR STM8 serial printf output

Recommended ReadingLatest update time:2024-11-16 15:47

Use of STM8's timer wake-up unit

The "RTC periodic wakeup unit" of STM8L can configure different wakeup periods through the WUCKSEL bits of the RTC_CR1 register. There are three specific modes: 　　1.1, WUCKSEL = 0xxb for short wakeup periods 　　1.2 WUCKSEL = 10xb for medium wakeup periods 　　1.3 WUCKSEL = 11xb for long wakeup periods The frequency divis

[Microcontroller]

Partial explanation of #define definitions in IAR 430 header files

Today, I found several questions when reading the header file cc430x613x.h in RF_Example_Code_v1.0. First, let's look at the three #define examples in cc430x613x.h: #define DEFC(name, address) __no_init volatile unsigned char name @ address; #define DEFW(name, address) __no_init volatile unsigned short name @ addr

[Microcontroller]

About Homemade STM8 Bootloader

Due to the needs of my project, I need to make a bootloader for STM8L052R8 for remote program upgrade function. For safety reasons, I will not use the bootloader that comes with ST, but my own bootloader. The basic functions are as follows. First, the program runs on a V1.0 version with BOOT. When the program receiv

[Microcontroller]

STM8 MCU reads DHT11 temperature and humidity sensor

DHT11 is a temperature and humidity sensor that is also driven by a bus. Its usage is very similar to that of the ds18b20 temperature sensor. Supply voltage 3.3~5.5V DC Measuring range: humidity 5% ~ 95%RH, temperature -20℃ ~ +60℃ Measurement accuracy humidity ±5%RH, temperature ±2℃ Resolution humidity 1%RH, tempera

[Microcontroller]

STM8 MCU reads DHT11 temperature and humidity sensor

STM8 Getting Started Learning and Experiments (I) GPIO and UART

Introduction: This chapter will describe how to configure GPIO and how to configure UART STM8 project template: http://download.csdn.net/detail/u012388993/9904051 The basic system configuration initialization function that will be used in these two experiments CLK_PeripheralClockConfig(CLK_PERIPHERAL_UART1, EN

[Microcontroller]

STM8 Getting Started Learning and Experiments (I) GPIO and UART

STM8 microcontroller triggers ADC synchronous sampling via PWM

The PWM function and ADC sampling function are the most commonly used functions in the development of digital switching power supplies. The sampling time point is very important when sampling ADC. The sample must be taken when the PWM output is high, so that the sampled data is the most accurate. In the STM8 microco

[Microcontroller]

vscode uses IAR_STM8 tool chain to compile and debug STM8 projects

This article describes how to use the IAR_STM8 tool chain on EIDE to complete project compilation and use STM8-Debug to complete debugging This article takes STM8S105K4T6 as an example 1. Create an 8/16 Bit MCU project using EIDE 2. Create a folder in the project directory and copy the STM8S standard peripheral l

[Microcontroller]

vscode uses IAR_STM8 tool chain to compile and debug STM8 projects

IAR for stm8 go to define solution can not jump

When I use IAR for stm8 go to define, I cannot jump, and the compiler does not give any prompts. I searched Baidu for many solutions but none of them worked. Finally, I found that I had to compile it once to make it work. Note: Don't compile directly, but make some changes to the code first and then compile it to mak

[Microcontroller]

IAR for stm8 go to define solution can not jump

Popular Resources
Popular amplifiers