Design of high brightness LED driver power supply without electrolytic capacitor based on MIP553

　　As a new type of electric light source, LED has obvious advantages in making large luminous three-dimensional characters and luminous signs. It has low control voltage, low cost and high reliability. Although LED products have an increasingly strong development trend in the domestic and foreign markets, LED lighting is an emerging industry after all and has not yet been widely popularized. Therefore, LED driver power supply inevitably has challenges in various aspects: First, since the forward voltage of the LED will change with the current and temperature, its "color point" will also drift with the current and temperature. In order to ensure the normal operation of the LED, its driver is required to limit the current regardless of the input conditions and forward voltage changes. Secondly, if LED dimming is required, pulse width modulation dimming technology is usually used, and the typical PWM frequency is 1~3kHz. Finally, the power handling capacity of the LED driver circuit must be sufficient and the function must be strong, able to withstand a variety of fault conditions, and easy to implement.

　　The solution introduced in this article uses the Panasonic MIP553 chip with built-in PFC dimmable LED driver circuit, and synthesizes it with an external non-isolated bottom-side chopper circuit as the basic circuit structure, outputting a stable current to meet the needs of LED operation. At the same time, a protection circuit is designed to protect the load. The experimental results show that the controller chip can work stably and can achieve a constant voltage output of 27V and a constant current output of 350mA.

　　The basic working principle of LED power supply

　　The BUCK converter and IPD control are used to realize the switching power supply, output constant current and voltage, and drive the LED lamp. The overall block diagram of the circuit is shown in Figure 1.

　　In the main circuit part, a filter is connected immediately after the mains power. Its function is to filter out the high-order harmonics and surges in the power supply, so that the control circuit is less disturbed by the power supply. The input rectifier part adopts an integrated rectifier bridge. Through the unidirectional conduction characteristics of the diode, the AC power with a level floating above and below the zero point is converted into a unidirectional pulsating DC power, and then the DC voltage is output under the action of the filter capacitor and inductor. After adjustment and control by the MIP553 and BUCK circuit, the voltage for LED use is output. Specific design of LED power supply

　　Input circuit design

　　In order to extend the service life of the LED driver and make it match the LED, the electrolytic capacitor in the circuit must be removed.

　　The design indicators of the circuit are: input AC voltage Vm: 198-264VAC/50Hz; output voltage Vo: 27VDC; output current Io: 0.35A.

　　The input circuit includes a noise filtering device, a safety insurance device and an input rectifying device, as shown in FIG2 .

　　The noise filter device is mainly composed of capacitors C1/C2/C3 and inductor L1. Its function is to reduce electromagnetic interference (EMI) in the frequency band less than 1MHz. This device can also be connected after the AC alternating current and before the rectifier, and its filtering effect is the same. The safety insurance device is composed of a fuse and ZNR1. The fuse is mainly used to prevent the peak current that is harmful to the circuit from being generated and quickly cut off the circuit to protect the load; ZNR1 is a surge absorber, which absorbs static electricity and surges from the input end to protect the subsequent circuit. The input rectifier converts AC power into DC power. The selection of the input rectifier bridge: The voltage stress of the rectifier bridge diode is:

　　Considering the margin, TSC GBL205 (VR=600V, IFAN=1A) is selected.

　　Output circuit design

　　The output circuit consists of a basic BUCK circuit and a voltage regulator diode DD1, as shown in Figure 3.

　　BUCK converter and its advantages

　　Buck converter, also known as step-down converter, series switching regulator, three-terminal switching step-down regulator, is a single-tube non-isolated DC/DC converter with an output voltage equal to or less than the input voltage.

　　The input current is in operation, when the switch is closed, is>0; when the switch is open, is=0, so is is pulsating, but the output current io is continuous and stable under the action of inductance, diode and capacitor. It is particularly suitable for providing working current for LED.

　　Selection criteria for FRD1: rated current greater than 2 times of output current, rated voltage greater than input voltage, reverse recovery time less than 100ns, considering margin, FRD1 parameters are: 15A, 600V, trr=50ns. Use similar method to select T1 and Cout, then their parameters are: T1: 680μH; Cout: 1μF, 50V.

　　Zener diode DD1

　　Within a certain range of low input voltage, if there is no reverse device like DD1, a reverse current will flow through the IPD at the moment the switch is turned off, and the IPD does not allow such a current because the reverse current will cause damage to the IPD.

　　The stresses on DD1 are: IDD>2·Io=2×0.35=0.7A, UDD>Uo, and reverse recovery time trr<100ns. Considering the margin, the selected parameters are: 3A/60V/75ns.

　　Protection Circuit

　　MIP553 has built-in protection circuits for overvoltage, overcurrent, overheating, and LED short circuit, but there is no design for protection circuit when LED is open circuit. The main ideas of protection circuit when LED is open circuit include voltage zener diode protection, transistor protection, bias coil protection, etc. Considering the cost and structure, the protection circuit with voltage zener diode is selected in this paper. Its circuit diagram is shown in Figure 3. When the LED is open circuit, the output voltage rises. If the output circuit has a voltage zener diode protection circuit, the voltage zener diode will embed the LED voltage below the voltage drop of the diode, thus preventing the output capacitor from being destroyed.

　　Control circuit design

　　The control circuit consists of MIP553 and its peripheral circuits, as shown in Figure 4.

　　The MIP553 chip realizes wide voltage 85~277V/AC input, built-in MOS, simple and stable structure, no need for electrolytic capacitors, supports isolation or non-isolation solutions, single power supply output power 6~30W, constant current output <1A. The power supply has overvoltage, overcurrent, and overheating protection functions, high safety and stability, small size, low heat generation, power efficiency ≥80%, power factor ≥95%, THD <20%.

　　The drain current of MIP553 is controlled by pins CL and EX, so the setting of resistors RCL and REX connecting these two pins will directly affect the size of the drain current. The maximum drain current can be determined by REX, and considering that this maximum drain current will flow through the LED, care should be taken when setting the reference value.

　　REX=（VDD（ON）-VEXH）/IEX=（6.5-2.8）/103=36kΩ (3)

　　Here, assume the input voltage is 100V, the output voltage is 28V, the current is 400mA, and the maximum drain current is set to 1.0A.

　　The functions of CVDD, CEX, and CCL are to stabilize the operation of MIP553 and suppress external noise. Therefore, their values ​​must be properly selected. CVDD stabilizes the voltage of VDD and suppresses the flickering of LED. Its characteristics are not affected by temperature and do not generate additional noise. The reference standard value is between 1 and 10μF. CEX suppresses external noise from entering the EX pin. Its reference standard value is between 470 and 1000pF. CCL suppresses external noise from entering the CL pin. If its value is too large, the pF value will be seriously affected. Therefore, its value should be less than 1000pF. Simulation results

　　The circuit is simulated using Multisim, and the results are shown in Figure 5.

　　As can be seen from Figure 5, the output voltage is stable at 27V and the current is stable at 0-35A, which meets the design requirements.

　　This article introduces the LED driver power supply designed using MIP553, and proves the stability of its output current through simulation, which has good application prospects.