The new 3 series of Tektronix oscilloscopes MDO, experience a high-definition large display on a compact and portable oscilloscope. The award-winning touch interface turns your learning curve into a step function. The unique built-in spectrum analysis function has been upgraded from optional to standard, and its function is very suitable for RF analysis. The 1GHz bandwidth model has been upgraded to 2 or 4 standard 1GHz passive probes, which doubles the overall performance of the 1GHz oscilloscope test system, and the rise time has been increased from 700ps to 350ps, which can test high-speed signals of tens or even hundreds of M signals.
Comparison of the indicators of Tektronix MDO new 3 series oscilloscopes and other brands of oscilloscopes:
Advantages of buying the new 3 series of Tektronix MDO oscilloscopes at Antai Test:
In addition to enjoying the 1GHz passive probe (TPP1000) and spectrum analyzer functions of the new Tektronix 3 Series MDO oscilloscope as standard, helping you easily save 50,000 yuan, you can also enjoy the following exclusive services:
1. Buy the new 3 series MDO from Tektronix and get a one-year warranty extension from Antai, which means the 3-year warranty from Tektronix is extended to 4 years;
2. When you purchase the new 3-series MDO from Tektronix, Antai Testing will provide free sample demonstration, sample trial, free technical support, product training and lifetime warranty services.
Previous article:Detailed Explanation of SPC Calibration Steps for Tektronix Oscilloscopes
Next article:Introduction to the functions and common classifications of signal sources
- Popular Resources
- Popular amplifiers
- Seizing the Opportunities in the Chinese Application Market: NI's Challenges and Answers
- Tektronix Launches Breakthrough Power Measurement Tools to Accelerate Innovation as Global Electrification Accelerates
- Not all oscilloscopes are created equal: Why ADCs and low noise floor matter
- Enable TekHSI high-speed interface function to accelerate the remote transmission of waveform data
- How to measure the quality of soft start thyristor
- How to use a multimeter to judge whether a soft starter is good or bad
- What are the advantages and disadvantages of non-contact temperature sensors?
- In what situations are non-contact temperature sensors widely used?
- How non-contact temperature sensors measure internal temperature
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
- Detailed explanation of intelligent car body perception system
- How to solve the problem that the servo drive is not enabled
- Why does the servo drive not power on?
- What point should I connect to when the servo is turned on?
- How to turn on the internal enable of Panasonic servo drive?
- What is the rigidity setting of Panasonic servo drive?
- How to change the inertia ratio of Panasonic servo drive
- What is the inertia ratio of the servo motor?
- Is it better for the motor to have a large or small moment of inertia?
- What is the difference between low inertia and high inertia of servo motors?
- How to use xilinx primitives.pdf
- BQ21040 single-cell lithium battery
- 【RPi PICO】Use SPI to drive WS2812
- NB-LOT Learning
- Looking for MPS2307 compatible chip
- Can anyone find the manual for this component?
- 【DFRobot wireless communication module】+GSM communication
- Register for MPS and you will get many surprises, including limited free power modules, motor drive evaluation boards, etc., on a first-come, first-served basis!
- A comprehensive summary of calculation formulas for 14 switching power supply topologies. Power supply engineers should save them for future use!
- DSP——C2000 Basics