fdtd 3D xyzPML MPI OpenMP

Recommended ContentMore

Open source project More

• Simple tablet 5.0 inches 800x480
• 【Training Camp】Garage Door Control-264738A
• Logic analyzer open source 8CH 24M sampling
• Four-axis remote control based on Xiaoma Ge
• test
• NCP10671B05GEVB: High Voltage Switch for Low Power Offline SMPS Evaluation Board
• [Internet of Things] Hongmeng Smart WIFI Switch +:4214059A
• MPC5777C BMSS and engine control development board
• DC 300V input BLDC motor without Hall control circuit using TPD4204F
• Four-way answering system

Searched by Users

• Samsung NAND Flash Memory Specification K9F4G08U0D
• MTK complete documentation (including DL, calibration, MMI function test)
• What is the difference between GND and GROUND, VCC, VDD, VEE, and VSS in the circuit?
• Renesas MCU Download Software
• Halcon9.0 programming technology detailed explanation
• Altium Designer Chinese Help Manual
• PDIUSBD12USB firmware programming and driver development Zhou LigongD12Win98 driver source code
• The registration code of altera quartus13--DDR2_three-speed Ethernet IP core
• Altium Designer Summer 09 Download Address Installation Crack Tutorial
• Switching power supply maintenance details

Just Take a LookMore

• How is the precise measurement of the Wheatstone bridge demonstrated?
  When measuring resistance values, the Wheatstone bridge is often mentioned. Why can using it improve the test accuracy? If you want to measure resistance, two resistors can also be measured. Are the f
• Giant 555 Timer
  Large 555
• [BearPi-HM Nano] Burning system and the first program
  In the previous article, the system has been successfully compiled. To verify whether the result is correct, the compiled system needs to be burned into the development board for further verification.
• [New ways to play SAMR21] 25. Using LPS22H sensor
  We have previously introduced how to use the LPS22 air pressure sensor in MakeCode. Now let’s introduce how to use it in CircuitPython.First of all, it should be noted that the I2C read and write func
• [N32L43X Review] 3. Hardware I2C drive OLED
  The previous article [N32L43X Review] 2. Simulating I2C to drive OLED introduced the use of GPIO to simulate I2C to drive OLED displays. This article introduces how to use the N32L43x hardware I2C1 po
• CC26x2R LaunchPad Development Kit
• MOSFET Failure Causes
• I am a hardware engineer who has been working for more than 1 year. I want to ask the experts about charging outside of work.
• Video: Introduction to mmWave Sensors
• What should I do if MP1584EN often burns the chip?

Trending Downloads

• UPMOST VG150 Digital Surveillance Card
• DDS Design Based on Verilog_HDL
• VHDL Design and Implementation of FM Demodulation and AFC Algorithm
• Development of OPC Data Server for Programmable Controller
• Power divider index comparison, manufacturer comparison selection
• AMS1117 Chinese information
• Stamping technology for coach frame components
• Capitel 450M Wireless Interventional System
• Three-phase three-level LLC resonant DC converter suitable for high voltage and high power applications - Hu Gaoping
• ADI Lithium Battery Test Equipment Solutions

Trending ArticlesMore

• Easter Egg丨This is an invitation letter, please check it (don’t miss the Easter Egg inside)
• “Not inferior to GPT-4”! Baidu’s most powerful model was released, and we tested it for the first time
• Infineon Technologies provides secure and convenient mobility solutions for smart cities
• Is demand reaching a turning point? 70% of Taiwan's top 10 semiconductor companies have seen a decline in performance
• A 6.1-magnitude earthquake occurred in Taiwan, and semiconductor companies responded
• MOTO G5 released, what did Lenovo get for $2.9 billion? 丨MWC 2017
• List of the largest domestic chip companies
• The official arrival of the wireless communication era
• Jen-Hsun Huang: If I could go back to 30 years old, I would not start Nvidia
• How to quickly get rid of the "technical newbie" hat - teach you how to play with the RZ microprocessor series in five days · STEP 5