PDIUSBD12USB firmware programming and driver development Zhou LigongD12Win98 driver source code

Recommended ContentMore

Open source project More

• Multifunctional PCB ruler
• Tian Xilin 1810300141 circuit
• Reminder water dispenser based on ESP32
• TDA7803A Evaluation Board-PowerSO36
• voltage follower
• PCF2131/PCA2131 Arduino ^® Shield expansion board
• Infrared+MQTT,ESP32C3+PWM brushless small ceiling fan
• 4056 automatic polarity conversion
• BA3570F headphone amplifier card: MBDBBDSL sound effects of old-fashioned CD players
• Tmp116_High_Accuracy_Temp_Sensor

Searched by Users

• J1939 Source Code
• ALTEAR FPGA MAX10 series Altium AD, orcad component library schematic package library
• High-resolution scanned version of \"Linux High-Performance Server Programming\" pdf
• EU RoHS Standard Download
• Multisim User Manual
• Renesas MCU Download Software
• LiChuang packaging library to pads
• Let\'s learn Cadence Allegro high-speed PCB design (Li Wenqing)
• GB 50150-2016 Electrical Equipment Acceptance Test Standard
• Model-Based Design and Embedded Implementation 444 pages 69.6M HD Bookmark Edition

Just Take a LookMore

• Motor stroke control problem
  Currently, a servo motor is used to drive the device to slide, and it will stop at a fixed position. This is currently achieved by photoelectric switches, but one problem with photoelectric switches i
• Help with the angle, acceleration conversion and accuracy of LSM6DSM
  [color=#008000][backcolor=rgb(255, 255, 255)][font=Tahoma,]Excuse me, how to convert the linear velocity and angular velocity of the six-axis data collected into angle and acceleration? Can LSM6DSM su
• Urgently looking for chip model
  Hello everyone, I work in RF, I don't know much about digital aspects, and I use few chips. Recently I am working on a project that requires using logic circuits to control the on and off of the RF sw
• ESP32-S3 KORVO-2 2.4'' ARDUINO TFT Unboxing Report
  After a long wait, the package finally arrived. Now I will make an unpacking report.First of all, the packaging box is very large.After unpacking, the upper and lower layers inside are protected by th
• A troubleshooting example of connecting XDS100V3 debugging target board with CCS
  Recently, when I used CCS to connect XDS100V3 to debug CC1310, I found that I could not connect to the target board. The following error is reported during Verify: [Start] Execute the command: %ccs_ba
• 【Android Development Learning Road】Part 2-- HelloEEWorld
• 51 MCU library serial port sends a segment of characters and the digital tube receives and displays them (use the serial port debugging assistant to modify the data)
• 【BearPi-HM Micro】Part 4: Familiar with the Openharmomy compilation framework and serial port interactive output
• 50 ways to use TI CC6678 digital signal processor (DSP)
• Share: How to reduce EMI and shrink power supply size with integrated active EMI filters

Trending Downloads

• Very good software, please download it
• Course Design Simulation Process Scheduling Management
• 1602 Character Manual.rar
• Temperature measurement and control system based on mc68hc908qy4 single chip microcomputer
• Key Points of Japanese Quality Control Department Manual
• In-vehicle wireless network intelligent anti-theft system
• Steel price list
• 16*16 LED display in hanzixianshi, with KEIL and PROTUES big.
• Application of NiosⅡ soft core in digital ultrasonic flaw detection system
• OCM240128-7.rar

Trending ArticlesMore

• Follow and comment to win gifts! Micron 2022 Taipei International Computer Show Keynote Speech Highlights: Data Center Special
• 2017 TIF In-depth Analysis | How to improve your power supply efficiency at every stage of design?
• Answer the question to win a prize | ADI's vital signs monitoring technology: monitoring the human body
• Practical Knowledge | 100 Basic Oscilloscope Knowledge You Need to Know About Both Software and Hardware
• A brief discussion on the debugging magic weapon of engineers (Part 2) --- the clever application of semihosting
• What is the connection between Fourier transform, Laplace transform and Z transform? Why do we need to perform transforms?
• I feel sorry for you who have to work overtime. Have you been exhausted today?
• WeChat has another reversal! The US Department of Justice once again requested to ban WeChat, and the US Micro-Enterprise Association said: We will fight to the end
• Samtec board-to-board connectors "three beauties" in one frame, which one is the most beautiful? Please vote~
• GTC22 | Listen to Mr. Huang Renxun's interpretation of AI and the Metaverse, and learn how to continuously break through and innovate in the real world