DVP04TC-E2 Thermocouple

Recommended ContentMore

Open source project More

• Microcontroller learning board 798274A based on stc8a8k32s4a12
• Simple FOC closed loop stepper motor
• Nano_Type-C_Measurer
• [Tuya Smart] Temperature and Humidity Sensor
• BLV one-point four-wire power supply
• Esp32 Performance Monitor_Main Control Board
• PRU Real-Time I/O Evaluation Reference Design
• Four-way answering system
• Inductive AC Power Loss Sensor
• audio amplifier

Searched by Users

• GB T50062-2008 Design specification for relay protection and automatic devices of power installations (1).pdf
• PSIM 2020 User Manual
• ADS1118 Driver
• Analog output (AO) based on LabviewCVI (DLL+DAQ)_Program case
• 24c08 driver This program is used to drive the I2C produced by ATM company. The 24c08 program gives the exit and entry
• Low Pin Interface (ULPI) Specification V1.1 (Chinese version).
• Design Patterns Explained - GoF 23 Design Patterns Analysis with C++ Source Code (Chinese Version) Non-photocopied PDF
• smith-chart smith chart impedance matching software--dedicated to users
• MAX485ESA Chinese data MAX485ESA data sheet pdf download
• 51 MCU Tutorial - Guo Tianxiang

Just Take a LookMore

• Introduction to Electromagnetic Compatibility by Clayton R.Paul
  "Introduction to Electromagnetic Compatibility" comprehensively and systematically describes the basic principles and design methods of electromagnetic compatibility. The book is divided into two part
• Stare at pictures to find inspiration
  [i=s]This post was last edited by btty038 on 2020-8-23 14:08[/i]Source: Electronic Forest, Author: Teacher SuI wish you all a happy weekend!
• Calculation of the ripple rate r of the second inductor of the SEPIC circuit
  Is it correct to use the following formula to calculate the inductance value for this type of SEPIC using coupled inductors?For other DCDC power topologies, the ripple rate of the inductor is r=VIN*D
• Common problems in designing microcontroller peripheral circuits
  1. Selection of pull-up resistor for MCUYou can see that when the resistor R1=10k in the reset circuit, RST is high level, and when R1=50, RST is low level. It is obvious that when R1=10k, it is wrong
• Smart connected lighting and the Internet of Things
  Humans are full of wisdom, so we invented devices that can provide us with light. In cities, towns and villages all over the world, people use the lighting equipment they created to illuminate dark pl
• [Chuanglong TLA40i-EVM development board] +01. Unboxing (zmj)
• Can the 66AK2L06 SoC enable miniaturization of test and measurement equipment?
• Does ThreadX open source have a big impact on other RTOS?
• Relay switching contacts do not open
• Some experience records of BLE-CC2541 project

Trending Downloads

• HFSS Antenna Simulation Basic Operation Guide
• SIM card standard
• uCOS-II source code that can be run based on AT91SAM7X256-EK under ADS
• Application of EWB in the Comprehensive Course Design of Digital Electronic Circuits
• Broadcom Wireless Development Board
• Core-based FPGA design method
• A serial communication program generated by interrupt mode, used on cygnal C8051F series microcontrollers
• Static routing and default routing
• ARM experiment five serial communication experiment
• Medium current relay

Trending ArticlesMore

• Chip fever goes down periodically: When it was crazy, the annual salary of fresh graduates was 500,000 yuan, but now it is difficult to enter a big factory with a 50% salary cut
• Practical skills | Analysis of classic op amp circuits
• Car companies make mobile phones? It is said that there is a small idea behind UWB
• [Major upgrade] STM32 HAL library 560 upgraded videos, recorded with real people, closer to real classroom! Knowledge points are explained from shallow to deep, nanny-level tutorials!
• [Smart instrument tools] Zhengdian Atomic DP100 CNC power supply, DS100 oscilloscope, T65 smart soldering iron, etc. are on sale!
• [H550 Intelligent Hot Air Gun] Portable digital display, rapid heating, accurate temperature control; brushless fan, fast heating and fast cooling; multiple protections, safe to use; modular design, intelligent control!
• [DL16 Logic Analyzer] The sampling rate is up to 1GHz, the hardware storage depth is up to 3.5G(bit), and it supports PWM output with adjustable frequency and duty cycle.
• [RK3568 Development Board] Domestic Rockchip microchip supports embedded AI development and supports Android, Linux and OpenHarmony operating systems!
• [Industrial Grade Project] The actual implementation of the single-channel high-precision industrial grade thermostat project is here! Atomic Brother platform launches industrial-grade training to easily master temperature control calibration/PID temperature control/modbus, etc.!