FULL SIZE D.I.L.
VOLTAGE
CONTROLLED
OSCILLATORS
HCMOS Logic, -40° to +85°C
M6001 thru M6007
L6001 thru L6007
M6021 thru M6023
L6021 thru L6023
HALF SIZE D.I.L.
H6001 thru H6007
H6021 thru H6023
Thru-Hole / Gull Wing, 5V
1 MHz to 125 MHz
Extended Temp
Thru-Hole VCXOs, 5V
Industrial temperature (-40°C to 85°C) thru-hole
5V VCXOs are available in a variety of off-the-
shelf models. Versions in full size (M) and half
size (H) cans are offered as standard designs.
These models are recommended for new
equipment in exacting environments that
operate at 5 volt. Five volt operation permits
extreme combinations of pull, control voltage
and center frequency deviation, enabling
the VCXO to accommodate a wide variety of
filtering and driving circuitry. Standard VCXOs
are hermetically sealed in full size (M) or half
size (H), DIL packages.
The many standard designs described here
have center frequency stability of ±50 ppm,
and frequency capture range to ±175 ppm.
These oscillators have excellent long-term
reliability, loading characteristics, and superior
startup performance. All VCXOs are tested and
guaranteed over the full operating temperature.
These 5V VCXOs generate an HCMOS frequency
output which is controlled by an input voltage.
The end-point frequency/voltage parameters are
defined, as is the center frequency.
CAPTURE RANGE
The Frequency-Capture range is equal to the (Center-Frequency ± the
Frequency Deviation), because every MF VCXO is ATE-tested to meet the
Frequency-Deviation over the temperature range.Frequency
Capture
specification includes all effects of temperature and supply voltage.
It is not necessary to make additional capture allowances.
FEATURES
•
Frequency from 1 MHz to 125 MHz
•
Capture-range is fully defined, under all conditions
•
Start-up time less than 5 ms.
•
Low profile package available above 60 MHz
•
Typical jitter is less than 15 ps RMS
•
Choice of thru-hole or gull wing
CONNECTIONS
Full
Size
Pin 1.
Pin 7.
Pin 8.
Pin 14.
Half
Size
Pin 1.
Pin 4.
Pin 5.
Pin 8.
Control Voltage, V
C
Ground & Case
Output
+5 Volts, V
DD
DOT
DENOTES
PIN 1
DOT
DENOTES
PIN 1
DOT
DENOTES
PIN 1
.52 MAX
SQUARE
.200 MAX
.215 MAX
.018
±
.001
.060 TYP
.300
±
.005
.400
.600
±
.005
Pin 1
.100
±
.005
Pin 7
.300
±.
005
.150
Pin 14
Pin 8
.250 MAX
.500
±
.005
8
5
.008/025 .15 MIN
.018
.300
Pin 1
1
4
.300
Pin 14
.2 MAX
.160
.2
MAX
.018
±
.001
.600
±
.005
Pin 7
.520
±
.005
.300
±.
005
Pin 8
GLASS INSULATORS (4)
on .48 x .18 ctrs.
1
8
.800
±
.005
DOT
DENOTES
PIN 1
.800
±
.005
.52 MAX
SQUARE
.200 MAX
.270 MAX
.018
.300
+.004
4
5
.300
+.004
.200 MAX
.070
GLASS INSULATORS (4)
on .48 x .18 ctrs.
Glass Insulators (4)
“M” Package – “L” Package
is same as “M”
but seated height is 0.190
“H” Package
“M” Package
with Gull Wing
“H” Package
with Gull Wing
ELECTRONICS
10 Commerce Drive, New Rochelle, NY10801
•
914-576-6570
•
Fax: 914-576-6204
•
http://www.mfelectronics.com
•
email:mfsales@mfelec.com
89
FULL SIZE D.I.L.
VOLTAGE CONTROLLED OSCILLATORS
HCMOS Logic, -40° to +85°C
Thru-Hole /Gull Wing, 5V
1 MHz to 125 MHz
M6001 thru M6007
L6001 thru L6007
M6021 thru M6023
L6021 thru L6023
HALF SIZE D.I.L.
H6001 thru H6007
H6021 thru H6023
Center Frequency is Between Two Voltages
with ±50 ppm stability
Control
Voltage
(Volts)
0.3 to 10.0
0.3 to 4.0
0.3 to 10.0
0.3 to 4.0
1.0 to 4.0
0 to 5.0
0.5 to 4.5
Frequency
Deviation
(ppm)
± 175 min
± 75 min
± 175 to 300
± 125 min
± 75 to 300
± 150 min
± 125 to 250
Guaranteed Control
Center
Capture
Voltage Frequency
Range
at Center Stability
(ppm)
Frequency
(ppm)
± 175
± 75
± 175
± 125
± 75
± 150
± 125
2.5 to 5.0
1.3 to 2.3
2.5 to 5.0
1.3 to 2.3
1.8 to 3.0
—
1.8 to 3.0
SPECIFICATIONS
Temperature
Operating
Storage
-40 to +85°C
–55 to +125°C
MODEL
6001
6002
6003
6004
6005
6006
6007
Frequency Stability
V
C
= 2.5V
±50 ppm, max.
MIN.
4.5
TYP
5.0
30
MAX
5.5
45
UNITS
volts
ma
± 40, typ
± 50, max
Input Voltage
Input Current
Output Levels (HCMOS)
“0” Level, sinking 16 ma.
“1” Level, sourcing 10 ma.
Rise and Fall Times, HCMOS
From 0.4 to (V
DD
-.4) V
(Above 35 MHz)
Symmetry
At V
DD
/ 2
Input Impedance,
Pin 5., Control Voltage
Control Voltage Bandwidth
Center Frequency is at 2.5V with ±50 ppm stability
Control
Voltage
(Volts)
0.5 to 4.5
0.5 to 4.5
0.5 to 4.5
Frequency
Deviation
(ppm)
± 75 to 150
± 100 to 200
± 150 to 300
Guaranteed Control
Center
Capture
Voltage Frequency
Range
at Center Stability
(ppm)
Frequency
(ppm)
± 75
± 100
± 150
2.5
2.5
2.5
± 30, typ
± 50, max
0.4
V
DD
-.4
volts
volts
MODEL
6021
6022
6023
2.5
4
2
ns
ns
.
45/55
percent
DESCRIPTIONS
M6001, H6001,
L6001
M6002, H6002,
L6002
M6003, H6003,
L6003
M6004, H6004,
L6004
M6005, H6005,
L6005
M6006, H6006,
L6006
M6007, H6007,
L6007
M6021, H6021,
L6021
M6022, H6022,
L6022
M6023, H6023,
L6023
±175 ppm, min. deviation when using
0.3 to 10V control-voltage
±75 ppm, min. deviation when using
0.3 to 4.0V control-voltage
±175 ppm to ±300 ppm deviation when using
0.3 to 10V control-voltage
±125 ppm deviation when using
0.3 to 4.0V control-voltage
±75 ppm to ±300 ppm deviation when using
1.0 to 4.0 control-voltage, for use where the
control voltage is 1 volt off both rails
±150 ppm, min. deviation when using
0 to 5.0 control-voltage
±125 ppm to ±250 ppm deviation when using
0.5 to 4.5 control-voltage
±75 ppm capture when using 0.5 to 4.5V
control-voltage and 2.5V center with 50 ppm stability
±100 ppm capture when using 0.5 to 4.5V
control-voltage and 2.5V center with 50 ppm stability
±150 ppm capture when using 0.5 to 4.5V
control-voltage and 2.5V center with 50 ppm stability
15
15
1000
150
Kohms
KHz
ENVIRONMENTAL SPECIFICATIONS
Temperature Cycle
– Not to exceed ±5 ppm change when exposed to 2
hours maximum at each temperature from 0 to 120°C, with 25°C reference
Shock
– 1000 G's, 0.35 ms, 1/2 sine wave, 3 shocks in each plane
Vibration
– 10-2000 Hz of .06" d.a. or 20 G's, whichever is less
Humidity
– Resistant to 85° R.H. at 85°C
PIN 1.
CONTROL VOLTAGE
V
DD
+3.3V
Power
Supply
GND
Half Size connections shown in ( )
To adapt Fet probe to receptacle
use Tektronix Part #103-0164-00
To connect output to scope use
use Tektronix Part #131-0258-00 (receptacle)
MA
1
(1)
14
(8)
FET PROBE
350 MHz
SCOPE
LOAD
Y-OUTPUT
7
(4)
8
(5)
COUNTER
FREQUENCY STABILITY
Frequency stability vs. Temperature is typically beter than ±40 ppm
for -40 to +85°C. Since the deviation of each oscillator is tested
and guaranteed over the whole operating temperature range, it is
not necessary to make additional capture allowances. All oscillators
will capture frequencies with the full minimum values of the deviation
under all conditions.
QUALITY
Each VCXO is computer-tested at three temperatures to guarantee
full compliance to the specification.
ALL OSCILLATORS HAVE INTERNAL BYPASS CAPACITORS
TEST CIRCUIT
ELECTRONICS
10 Commerce Drive, New Rochelle, NY10801
•
914-576-6570
•
Fax: 914-576-6204
•
http://www.mfelectronics.com
•
email:mfsales@mfelec.com
90
FULL SIZE D.I.L.
VOLTAGE CONTROLLED OSCILLATORS
HCMOS Logic, -40° to +85°C
Thru-Hole /Gull Wing, 5V
1 MHz to 125 MHz
M6001 thru M6007
L6001 thru L6007
M6021 thru M6023
L6021 thru L6023
HALF SIZE D.I.L.
H6001 thru H6007
H6021 thru H6023
MECHANICAL SPECIFICATIONS
Gross Leak
– Each unit checked in 125°C flurocarbon
Fine Leak
– Mass spectrometer leak rate less than 2 X 10-8 atmos,
cc/sec of helium
Pins
– Kovar, nickel plated with 60/40 solder coat
Bend Test
– Will withstand two bends of 90° from reference
Header
– Steel, with nickel platel
Case
– Stainless steel, type 304
Marking
– Printing is black epoxy ink
Resistance to Solvents
– MIL STD 202, Method 215
AGING
Fig. 1 M6022-16.384M,
with 50 pf load
3 ppm, first year, typ.
1 ppm per year thereafter, typ.
M6022 -16.384M, TYPICAL
200
150
250
200
150
4.5 Volts
100
50
0
0
-50
-50
-100
-150
-200
-250
0.0 0.5
1.0 1.5
2.0 2.5
3.0 3.5
4.0 4.5
5.0
Temp -40°C
Temp 0°C
Temp 25°C
Temp 85°C
-100
0.5 Volts
-150
-200
0 Volts
-250
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100
0
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100
10
20
30
40
2.5 Volts
50
60
5.0 Volts
80
70
V
DD
= 4.5V
V
DD
= 5.0V
V
DD
= 5.5V
Frequency Deviation, ppm
100
50
Control Voltage, Vc
Temperature,
°C
Temperature,
°C
Fig. 2 Frequency vs. Control Voltage
Fig. 3 Frequency vs. Temperature
Fig. 4 Frequency vs. Temperature @ 2.5V
Control Voltage
HOW TO ORDER
For Part Number, put package type before model number,
and add frequency in MHz, for example:
M 6 0 0 1- 1 2 . 3 5 2 M G
“M” is full size DIL
“H” is half size DIL
“L” is low height,
full size DIL
“6001”
is model
type
“12.352 M”
frequency in MHz
Add
“G”
for
gullwing
ELECTRONICS
10 Commerce Drive, New Rochelle, NY10801
•
914-576-6570
•
Fax: 914-576-6204
•
http://www.mfelectronics.com
•
email:mfsales@mfelec.com
91
PCB Design
京公网安备 11010802033920号
EEWORLD
