• These low noise power supplies are FCC class B compliant.
PART NUMBERS AND RATINGS
Part No.
FCP-031
FCP-031B
FCP-032
FCP-032B
FCP-101
FCP-101B
FCP-102
FCP-102B
Maximum output power Output 1(V
1
)
(W)
Voltage(V)
2.9
3
9.6
9.6
+12
+15
+12
+15
FCP, FCP-B Series
Current(A)
0.01 to 0.12
0.01 to 0.1
0.04 to 0.4
0.03 to 0.32
Output 2(V
2
)
Voltage(V)
–12
–15
–12
–15
Current(A)
0.01 to 0.12
0.01 to 0.1
0.04 to 0.4
0.03 to 0.32
TERMINAL DESIGNATIONS AND FUNCTIONS
V.ADJ
1
V
1
0V
V
2
+15V
0.32A
DC OUTPUT
–15V
0.32A
POWER SUPPLY
FCP-102
2
3
100-120V
50-60Hz
L
0.35A
AC INPUT
N
Terminal No. 1: DC output terminals(V
1
, 0V, V
2
)
Connect to load.
V
1
:+output
0V:V
1
, V
2
ground
V
2
:–output
Terminal No. 2: Ground terminal( )
For input line.
Terminal No. 3: AC input terminals(L, N, AC INPUT)
Connect to AC. 100 to 120V single phase power supply.
Specifications which provide more details for the proper and safe use of the described product are available upon request.
All specifications are subject to change without notice.
Power Supplies
AC Input
Multi Output, General-Purpose
SPECIFICATIONS
3W TYPE
Part No.
Output voltage, current
∗
1
V
1
V
2
W
FCP-031
FCP-031B
+12V • 0.12A
–12V • 0.12A
2.9
FCP, FCP-B Series
Maximum output power
Input requirements
Input voltage Eac
V
Input frequency
Hz
Input current
A
Surge current
A
Leakage current
mA
Efficiency
%
Output characteristics
Rated output voltage
V
Voltage variable range
V
A
Maximum output current
∗1
∗2
A
Minimum output current
V
Output setting con- Voltage
ditions
Current
A
Input variation
%
Load variation
%
Temperature
Voltage stability
%
variation
Drift
%
Dynamic load
%/ms
Ripple Ep-p
mV
Ripple noise Ep-p
mV
Start up time
ms
Hold up time
ms
Accessory equipment
Operation indicator
Overvoltage protection
Overcurrent protection
Remote ON-OFF
Remote sensing
Output voltage external variable function
Standards
Safety standards
Noise terminal voltage
Construction
External dimensions H×W×L
mm
Weight
g
Mounting method
Case and cover
Input and output cables
∗
1
Current
∗
2
The
FCP-032
FCP-032B
+15V • 0.1A
–15V • 0.1A
3
85 to 132[Rating:100-120]
47 to 66[Single phase][Rating:50-60]
0.08typ.[85V, 25°C, input and output ratings](Output rating:0.1max.)
16max.[25°C, input and output ratings, cold start]
0.5max.[25°C, input and output ratings]
64typ.[25°C, input and output ratings]
–12[V
2
]
+12[V
1
]
10.8 to 13.2[V
2
varies simultaneously as V
1
.]
0.12
0.12
0.01
0.01
12.1
—
0.12
0.12
0.1typ.[Within the input voltage range]
0.8typ.[10 to 100% load]
1typ.[0 to +50°C ]
1max.[25°C, input and output ratings, after input voltage ON for 30min to 8h]
±4max./1max.[50 to 100% sudden load change]
80
150
100max.
20min.
None
Uses overvoltage prevention
∗3
Fixed voltage threshold type, automatic recovery.
None
None
None
UL478, CSA ELECTRICAL BULLETIN No.1402 approved.
FCC class B compliant.
19×55×50[Except input and output terminals]
80max.
Can be attached to 1side.
Nonflammable resin
—
+15[V
1
]
–15[V
2
]
13.5 to 16.5[V
2
varies simultaneously as V
1
.]
0.1
0.1
0.01
0.01
15.1
—
0.1
0.1
Total variation ±3max.(±1typ.)
rating(maximum output current) is determined for 0 to +50°C. Derating is required when used outside this temperature range.
output load variation is determined within the range set by the minimum output current and the maximum output current. Nominal values might pos-
sibly not be satisfied when output is below the minimum output current.
∗
3
Although there is no built-in overvoltage protection circuit, the overvoltage prevention method is used for circuit design, thereby preventing overvoltage.
Specifications which provide more details for the proper and safe use of the described product are available upon request.
All specifications are subject to change without notice.
Power Supplies
AC Input
Multi Output, General-Purpose
SPECIFICATIONS
10W TYPE
Part No.
Output voltage, current
∗
1
V
1
V
2
W
FCP-101
FCP-101B
+12V • 0.4A
–12V • 0.4A
9.6
FCP, FCP-B Series
Maximum output power
Input requirements
Input voltage Eac
V
Input frequency
Hz
Input current
A
Surge current
A
Leakage current
mA
Efficiency
%
Output characteristics
Rated output voltage
V
Voltage variable range
V
A
Maximum output current
∗1
∗2
A
Minimum output current
V
Output setting con- Voltage
ditions
Current
A
Input variation
%
Load variation
%
Temperature
Voltage stability
%
variation
Drift
%
Dynamic load
%/ms
Ripple Ep-p
mV
Ripple noise Ep-p
mV
Start up time
ms
Hold up time
ms
Accessory equipment
Operation indicator
Overvoltage protection
Overcurrent protection
Remote ON-OFF
Remote sensing
Output voltage external variable function
Standards
Safety standards
Noise terminal voltage
Construction
External dimensions H×W×L
mm
Weight
g
Mounting method
Case and cover
Input and output cables
∗1
Current
∗2
The
FCP-102
FCP-102B
+15V • 0.32A
–15V • 0.32A
9.6
85 to 132[Rating:100-120]
47 to 66[Single phase][Rating:50-60]
0.25typ.[85V, 25°C, input and output ratings](Output rating :0.1max.)
16max.[25°C, input and output ratings, cold start]
0.5max.[25°C, input and output ratings]
75typ.[25°C, input and output ratings]
–12[V
2
]
+12[V
1
]
10.8 to 13.2[V
2
varies simultaneously as V
1
.]
0.4
0.4
0.04
0.04
12.1
—
0.4
0.4
0.1typ.[Within the input voltage range]
0.8typ.[10 to 100% load]
1typ.[0 to +50°C ]
1max.[25°C, input and output ratings, after input voltage ON for 30min to 8h]
±4max./1max.[50 to 100% sudden load change]
80
150
100max.
20min.
None
Uses overvoltage prevention
∗3
Fixed voltage threshold type, automatic recovery.
None
None
None
UL478, CSA ELECTRICAL BULLETIN No.1402 approved.
FCC class B compliant.
19×55×80[Except input and output terminals]
100max.
Can be attached to 1side.
Nonflammable resin
—
+15[V
1
]
–15[V
2
]
13.5 to 16.5[V
2
varies simultaneously as V
1
.]
0.32
0.32
0.03
0.03
15.1
—
0.32
0.32
Total variation ±3max.(±1typ.)
rating(maximum output current) is determined for 0 to +50°C. Derating is required when used outside this temperature range.
output load variation is determined within the range set by the minimum output current and the maximum output current. Nominal values might possi-
bly not be satisfied when output is below the minimum output current.
∗
3
Although there is no built-in overvoltage protection circuit, the overvoltage prevention method is used for circuit design, thereby preventing overvoltage.
A152_FCP
980403
Specifications which provide more details for the proper and safe use of the described product are available upon request.
All specifications are subject to change without notice.
Where are you planning to go during the May Day holiday? Leave a message and share the beautiful scenery you see!Source: WeChat official account: City of Craftsmanship
I have seen so many mountains, r...
Can a potentiometer that can rotate multiple circles be used to detect the rotation of the steering wheel? What I am considering here is the wear and tear of the potentiometer caused by the speed of r...
After spending a few days, I finally downloaded a mobile APP with the help of teacher bigbat. After repeated attempts, I was finally able to receive the data sent by SHT31.
This mobile APP is provided...
[size=4]There are two marking methods for SMD diodes: letter, number code or letter + number code marking method and color (code) marking method. For example, the electrical parameters of "A3" are as ...
I want to learn FPGA recently. I have read Verilog syntax and am ready to start writing programs. I have a few questions. Question 1: Where can I download Quartus software? I can't download it on Inte...
A photovoltaic grid-connected power generation system based on the combination of repetitive control and grid voltage feedforward control is proposed. Repetitive control can suppress periodic load dis...
Xilinx, a global leader in adaptive and intelligent computing, announced that its artificial intelligence platform Zynq UltraScale+ MPSoC ZCU104 evaluation kit won six performance champions in the bo...[Details]
Introduction
Discrete
difference amplifiers
with op amps and external gain-setting resistors
have mediocre accuracy and significant temperature drift. Using 1%, 100ppm/°C stan...[Details]
SAP, Amdocs, Getty Images are first to use NVIDIA AI Foundation Models Build a custom LLM, train on the NVIDIA DGX cloud, and deploy using NVIDIA AI Enterprise software Microsoft Ignite — ...[Details]
In order to catch up with the last wave of 630, construction units of various projects are working intensively. However, the qualifications of construction contractors vary greatly, and the differe...[Details]
Introduction
An essential process in automobile development is to test and simulate the bus. If there is a tool that can simulate bus communication traffic, it will be much easier ...[Details]
A three-phase motor means that when the three-phase stator winding of the motor (each phase differs by 120 degrees electrical angle) is supplied with three-phase alternating current, a rotating mag...[Details]
Users have been reporting in recent days that Apple's Messages app is still sending read receipts even though the setting has been disabled. This isn't a new problem, but it is a recurring bug in iOS...[Details]
The development of China's new energy in the past 20 years has not been as rapid as the last two years. As one of the "three major components" of electric vehicles, batteries are undergoing wave afte...[Details]
Recently, Gokewei disclosed a clarification announcement stating that the rumors about the company's chip cooperation with Huawei HiSilicon are false information, and the company has no cooperation o...[Details]
STMicroelectronics (NYSE: STM), a global semiconductor leader serving customers across the spectrum of electronics applications, and SYSGO, a world-leading developer of European certifiable embedded ...[Details]
The SysTick timer is bundled in the NVIC and is used to generate the SysTick exception (exception number: 15). In the past, the operating system and all systems that used a time base had to have a har...[Details]
According to foreign media reports, on February 11 local time, Hyundai Motor Company announced that it will expand its partnership with the U.S. Department of Energy (DOE) to further support the DOE'...[Details]
A fully integrated ultra-wideband CMOS RF transceiver switch chip with low insertion loss and high isolation is designed. The circuit adopts deep N-well suspension technology. Under the power supply ...[Details]
On October 30, GeoMate, a leading-edge mapping solutions provider, announced a partnership with dSPACE, a simulation and validation solutions provider, to accelerate the development of advanced dri...[Details]