• These low noise power supplies are FCC class B compliant.
PART NUMBERS AND RATINGS
Part No.
FCP-031
FCP-031B
FCP-032
FCP-032B
FCP-101
FCP-101B
FCP-102
FCP-102B
Maximum output power Output 1(V
1
)
(W)
Voltage(V)
2.9
3
9.6
9.6
+12
+15
+12
+15
FCP, FCP-B Series
Current(A)
0.01 to 0.12
0.01 to 0.1
0.04 to 0.4
0.03 to 0.32
Output 2(V
2
)
Voltage(V)
–12
–15
–12
–15
Current(A)
0.01 to 0.12
0.01 to 0.1
0.04 to 0.4
0.03 to 0.32
TERMINAL DESIGNATIONS AND FUNCTIONS
V.ADJ
1
V
1
0V
V
2
+15V
0.32A
DC OUTPUT
–15V
0.32A
POWER SUPPLY
FCP-102
2
3
100-120V
50-60Hz
L
0.35A
AC INPUT
N
Terminal No. 1: DC output terminals(V
1
, 0V, V
2
)
Connect to load.
V
1
:+output
0V:V
1
, V
2
ground
V
2
:–output
Terminal No. 2: Ground terminal( )
For input line.
Terminal No. 3: AC input terminals(L, N, AC INPUT)
Connect to AC. 100 to 120V single phase power supply.
Specifications which provide more details for the proper and safe use of the described product are available upon request.
All specifications are subject to change without notice.
Power Supplies
AC Input
Multi Output, General-Purpose
SPECIFICATIONS
3W TYPE
Part No.
Output voltage, current
∗
1
V
1
V
2
W
FCP-031
FCP-031B
+12V • 0.12A
–12V • 0.12A
2.9
FCP, FCP-B Series
Maximum output power
Input requirements
Input voltage Eac
V
Input frequency
Hz
Input current
A
Surge current
A
Leakage current
mA
Efficiency
%
Output characteristics
Rated output voltage
V
Voltage variable range
V
A
Maximum output current
∗1
∗2
A
Minimum output current
V
Output setting con- Voltage
ditions
Current
A
Input variation
%
Load variation
%
Temperature
Voltage stability
%
variation
Drift
%
Dynamic load
%/ms
Ripple Ep-p
mV
Ripple noise Ep-p
mV
Start up time
ms
Hold up time
ms
Accessory equipment
Operation indicator
Overvoltage protection
Overcurrent protection
Remote ON-OFF
Remote sensing
Output voltage external variable function
Standards
Safety standards
Noise terminal voltage
Construction
External dimensions H×W×L
mm
Weight
g
Mounting method
Case and cover
Input and output cables
∗
1
Current
∗
2
The
FCP-032
FCP-032B
+15V • 0.1A
–15V • 0.1A
3
85 to 132[Rating:100-120]
47 to 66[Single phase][Rating:50-60]
0.08typ.[85V, 25°C, input and output ratings](Output rating:0.1max.)
16max.[25°C, input and output ratings, cold start]
0.5max.[25°C, input and output ratings]
64typ.[25°C, input and output ratings]
–12[V
2
]
+12[V
1
]
10.8 to 13.2[V
2
varies simultaneously as V
1
.]
0.12
0.12
0.01
0.01
12.1
—
0.12
0.12
0.1typ.[Within the input voltage range]
0.8typ.[10 to 100% load]
1typ.[0 to +50°C ]
1max.[25°C, input and output ratings, after input voltage ON for 30min to 8h]
±4max./1max.[50 to 100% sudden load change]
80
150
100max.
20min.
None
Uses overvoltage prevention
∗3
Fixed voltage threshold type, automatic recovery.
None
None
None
UL478, CSA ELECTRICAL BULLETIN No.1402 approved.
FCC class B compliant.
19×55×50[Except input and output terminals]
80max.
Can be attached to 1side.
Nonflammable resin
—
+15[V
1
]
–15[V
2
]
13.5 to 16.5[V
2
varies simultaneously as V
1
.]
0.1
0.1
0.01
0.01
15.1
—
0.1
0.1
Total variation ±3max.(±1typ.)
rating(maximum output current) is determined for 0 to +50°C. Derating is required when used outside this temperature range.
output load variation is determined within the range set by the minimum output current and the maximum output current. Nominal values might pos-
sibly not be satisfied when output is below the minimum output current.
∗
3
Although there is no built-in overvoltage protection circuit, the overvoltage prevention method is used for circuit design, thereby preventing overvoltage.
Specifications which provide more details for the proper and safe use of the described product are available upon request.
All specifications are subject to change without notice.
Power Supplies
AC Input
Multi Output, General-Purpose
SPECIFICATIONS
10W TYPE
Part No.
Output voltage, current
∗
1
V
1
V
2
W
FCP-101
FCP-101B
+12V • 0.4A
–12V • 0.4A
9.6
FCP, FCP-B Series
Maximum output power
Input requirements
Input voltage Eac
V
Input frequency
Hz
Input current
A
Surge current
A
Leakage current
mA
Efficiency
%
Output characteristics
Rated output voltage
V
Voltage variable range
V
A
Maximum output current
∗1
∗2
A
Minimum output current
V
Output setting con- Voltage
ditions
Current
A
Input variation
%
Load variation
%
Temperature
Voltage stability
%
variation
Drift
%
Dynamic load
%/ms
Ripple Ep-p
mV
Ripple noise Ep-p
mV
Start up time
ms
Hold up time
ms
Accessory equipment
Operation indicator
Overvoltage protection
Overcurrent protection
Remote ON-OFF
Remote sensing
Output voltage external variable function
Standards
Safety standards
Noise terminal voltage
Construction
External dimensions H×W×L
mm
Weight
g
Mounting method
Case and cover
Input and output cables
∗1
Current
∗2
The
FCP-102
FCP-102B
+15V • 0.32A
–15V • 0.32A
9.6
85 to 132[Rating:100-120]
47 to 66[Single phase][Rating:50-60]
0.25typ.[85V, 25°C, input and output ratings](Output rating :0.1max.)
16max.[25°C, input and output ratings, cold start]
0.5max.[25°C, input and output ratings]
75typ.[25°C, input and output ratings]
–12[V
2
]
+12[V
1
]
10.8 to 13.2[V
2
varies simultaneously as V
1
.]
0.4
0.4
0.04
0.04
12.1
—
0.4
0.4
0.1typ.[Within the input voltage range]
0.8typ.[10 to 100% load]
1typ.[0 to +50°C ]
1max.[25°C, input and output ratings, after input voltage ON for 30min to 8h]
±4max./1max.[50 to 100% sudden load change]
80
150
100max.
20min.
None
Uses overvoltage prevention
∗3
Fixed voltage threshold type, automatic recovery.
None
None
None
UL478, CSA ELECTRICAL BULLETIN No.1402 approved.
FCC class B compliant.
19×55×80[Except input and output terminals]
100max.
Can be attached to 1side.
Nonflammable resin
—
+15[V
1
]
–15[V
2
]
13.5 to 16.5[V
2
varies simultaneously as V
1
.]
0.32
0.32
0.03
0.03
15.1
—
0.32
0.32
Total variation ±3max.(±1typ.)
rating(maximum output current) is determined for 0 to +50°C. Derating is required when used outside this temperature range.
output load variation is determined within the range set by the minimum output current and the maximum output current. Nominal values might possi-
bly not be satisfied when output is below the minimum output current.
∗
3
Although there is no built-in overvoltage protection circuit, the overvoltage prevention method is used for circuit design, thereby preventing overvoltage.
A152_FCP
980403
Specifications which provide more details for the proper and safe use of the described product are available upon request.
All specifications are subject to change without notice.
mmWave is a valuable sensing technology that can be used to detect objects and provide information about their distance, speed and angle. It is a contactless technology that operates in the 30GHz to 3...
[size=4]Many people will find that the wireless Internet access of the computer at home is called WLAN, while the Internet access of mobile phones or tablets is called WIFI. They are the same wireless...
It is probably that a PWM wave of a certain frequency is generated by the clock. Using FPGA can get a more perfect waveform, but if only a CLK wave is provided, F5529LP can do it completely. #includeu...
if(Bianxing[0]>0) Bianxing[0]--; There are two sentences in the program. The array Bianxing[6] is long int. When debugging, I found that if Bianxing[0]=1, it will become 0XBF80000 after decrementing. ...
There is a question I have always wanted to ask. In a circuit board, if I have already filtered the wave at the power supply and processed it, can I add a few less capacitors at the MCU? For example, ...
Today, Zeng Kunpeng, general manager of the iQOO product line, released a poster officially confirming the name of the new iQOO Neo phone that has been widely circulated on the Internet and is equipp...[Details]
#include "kernel.h" unsigned int PWM_Buf ; //6-channel PWM frequency unsigned long timer0_ticks; unsigned long timer0_tickssec; unsigned long timer1_ticks; unsigned long timer1_ticksmin; unsigned l...[Details]
The physical design of the PCB board is the last step in the design of switching power supplies. If the design method is not appropriate, the PCB may radiate too much electromagnetic interference, ...[Details]
Datang Telecom said on the interactive platform that the company closely follows the group's unified layout in 5G. With the development of 5G applications, the company will consider related expansion...[Details]
On May 30, Lei Jun, founder, chairman and CEO of Xiaomi, posted on his personal Weibo that the Xiaomi IoT platform has connected to 351 million smart hardware. 5月26日,小米集团公布2021年第一季度业绩。总营收达人民币769亿元,...[Details]
1 Overview
In recent years, as
part of the
semiconductor
lighting field, neon lights and some traditional light sources for urban landscape
lighting
and indoor and out...[Details]
An electronic oscilloscope is an instrument used to measure the shape of alternating current or pulse current waves. It consists of a tube amplifier, a scanning oscillator, a cathode ray tube, etc....[Details]
Apple plans to launch Mac computers with its own processors next year, according to Bloomberg. Bloomberg further pointed out that Apple is currently researching three Mac processors, which are chi...[Details]
March 13, 2024 — In a major breakthrough, OpenAI spinoff Covariant announced the success of building a new artificial intelligence model that enables
robots
to learn to perform a variety of...[Details]
Abstract: This article introduces the implementation ideas, methods, communication protocols and C51 program platform of batch processing commands for communication between PC and MCS-51 microco...[Details]
According to foreign media reports, DENSO Corporation (DENSO) and NTT Communications Corporation (NTT Com) will begin verifying the Vehicle Security Operation Center (V-SOC) technology jointly develo...[Details]
There are some switches on the operation panel of electronic equipment, most of which are mechanical ON/OFF switches. Although mechanical key control technology is very mature, the circuit structure...[Details]
;================================================== ;DS1302 control subroutine ;====================================================== ;The program includes: DS1302 initialization, time data wr...[Details]
"In the future, you can preset many scenes such as the air conditioner and water heater at home in the car. Such interconnected scenes are not realized by asking people to buy some new products, ...[Details]
This application note provides design guidelines for the optomechanical part of the MAX25205 and MAX25405 gesture sensors. A key design issue in gesture detection systems based on infrared (IR) tec...[Details]