1 mm Straight, Surface Mount, With Power Ground Option
•
•
•
•
PK10M Series
1 mm pitch connector system
Four mating heights available
Available power contacts rated at 5A
Available frame ground connection through
surface mount retention clips
• Keyed design helps prevent mating
misalignment
• See Regulatory Information Appendix (RIA)
for chemical compliance information
Date Modified: September 14, 2007
TS-1152-B
Sheet 1 of 3
Physical
Insulation
Material:
Glass Filled LCP
Flammability:
UL 94V-0
Color:
Black
Materials
Signal Contact:
Copper Alloy
Power Contact:
Copper Alloy
Retention Clips:
Copper Alloy
Contact Plating
Underplating:
120 µ" [ 3.0 µm ] Nickel
Wiping Area:
4 µ" [ 0.10
μm
] min. Gold
Solder Tails:
Gold Flash
Retention Clip Plating:
Tin Copper over 120 µ" [ 3.0 µm ] Nickel
Marking:
Polarity Identification, Lot Number
Electrical
Current Rating:
0.5 A per Signal Contact, 5 A Power Contact
Insulation Resistance:
1 × 10
3
MΩ min at 250 V
DC
Withstanding Voltage:
300 V
AC
for 1 minute
Environmental
Temperature Rating:
-55°C to +85°C
Process Rating:
Maximum
260°C
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M
™
Pak 10 Media Socket
1 mm Straight, Surface Mount, With Power Ground Option
Socket with Power Contacts
Contact
Quantity
40
50
60
80
A
32.40
[1.276]
37.40
[1.472]
42.40
[1.669]
52.40
[2.063]
B
32.00
[1.260]
37.00
[1.457]
42.00
[1.654]
52.00
[2.047]
C
29.40
[1.157]
34.40
[1.354]
39.40
[1.551]
49.40
[1.945]
D
25.40
[1.000]
30.40
[1.197]
35.40
[1.394]
45.40
[1.787]
E
22.40
[0.882]
27.40
[1.079]
32.40
[1.276]
42.40
[1.669]
F
20.80
[0.819]
25.80
[1.016]
30.80
[1.213]
40.80
[1.606]
G
19.00
[0.748]
24.00
[0.945]
29.00
[1.142]
39.00
[1.535]
PK10M Series
Ordering Information
PK10M - XXXSX - SMT - DA
(RIA E1 & C1 apply)
Contact Quantity
See Table
P = With Power Contacts
Omit = Without Power Contacts
TS-1152-B
Sheet 2 of 3
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M
™
Pak 10 Media Socket
1 mm Straight, Surface Mount, With Power Ground Option
Socket without Power Contacts
Contact
Quantity
40
50
60
80
A
30.40
[1.197]
35.40
[1.394]
40.40
[1.591]
50.40
[1.984]
B
30.00
[1.181]
35.00
[1.378]
40.00
[1.575]
50.00
[1.969]
C
27.40
[1.079]
32.40
[1.276]
37.40
[1.472]
47.40
[1.866]
D
24.60
[0.969]
29.60
[1.165]
34.60
[1.362]
44.60
[1.756]
E
22.40
[0.882]
27.40
[1.079]
32.40
[1.276]
42.40
[1.669]
F
20.80
[0.819]
25.80
[1.016]
30.80
[1.213]
40.80
[1.606]
G
19.00
[0.748]
24.00
[0.945]
29.00
[1.142]
39.00
[1.535]
PK10M Series
TS-1152-B
Sheet 3 of 3
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/17/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217B-b
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means
that the product or part
does not
contain any of the following substances in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part
does
contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase.
3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.
Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
I am a beginner. My graduation project is the design of power management system for lithium battery. I want to design according to the guide book of power monitoring and balancing design of TI company...
How much current can a 0Ω resistor carry? This question must have been asked by every hardware engineer. And there is another related question, which is how big the resistance of a 0Ω resistor is?Thes...
Overview of Ad Hoc Network EquipmentThe MESH wireless self-organizing network multimedia broadband transmission system is a mobile broadband multimedia communication system designed with a new "wirele...
It is good that the forum moderator organized this activity. It can form a long-term activity and let everyone share some of their practical experience. The time is short, so I will share a simple one...
Figure 1
A diagram of the 3-wire analog output module is shown in Figure 1. The module uses a dual-channel DAC8562 digital-to-analog converter (DAC) to drive the voltage and current output stages of t...
Earlier we learned how to light up the LED lights, and then we learned how to make the LED lights flash. Now we need to learn more about how to make the 8 lights light up one by one in turn and make...[Details]
Introduction: Everyone knows that ICC-AVR cannot debug code, and many people choose AVRStudio. However, AVR Studio is not intuitive, especially when debugging LCD display code, you cannot see the dis...[Details]
Contactless payments went mainstream during the pandemic. Mastercard reported that contactless payment transactions grew 40% in the first quarter of 2020, and by 2021, 51% of Americans were using som...[Details]
1. Development of smart grid
1.1 American Recovery and Reinvestment Act
On February 17, 2009, President Obama signed the American Recovery and Reinvestment Act (ARRA) of 2009. This act pro...[Details]
Preface
Today, when designing and building control systems, engineers always hope to use fewer devices to achieve more functions.
Especially today, they need control systems that can ...[Details]
According to foreign media reports, Italian car manufacturer Abarth has begun testing facial recognition technology to better understand the experience of drivers and passengers in the car. The carma...[Details]
In the 51 single-chip microcomputer application system, when the serial port is not used for communication, it can be used to expand the parallel I/O port (set the serial port to work in mode O, sh...[Details]
Without using hands or keyboard, just relying on thoughts, 691.55 bits can be output on the computer screen per minute, which is equivalent to 69 Chinese characters per minute. Output 691.55 bits p...[Details]
Lithium-ion batteries are widely used in portable electronic devices such as mobile phones, camcorders, laptops, cordless phones, power tools, remote control or electric toys, cameras, etc. due to th...[Details]
With the massive increase in system design complexity and integration,
electronic
system designers are engaged in
circuit
design
above 100MHZ
, and
the operating frequency of
the ...[Details]
Abstract: An automatic line-following wheeled walking robot control system is designed, using the AT89S52 microcontroller as the main control CPU, plus a complex programmable logic device (CPID) to as...[Details]
Light changes the world
For hundreds of years, physicists' understanding and interpretation of "light" has evolved from "wave theory" to "particle theory" and then to "quantum theory" of li...[Details]
I used the STM32F10X firmware library and practiced the simplest port application, which seems to be very convenient.
/******************** GPIO application********************
stm32 library file a...[Details]
The use of electrical equipment is a necessity in daily life. All heating equipment must have a thermal protector installed to avoid overheating of the electrical appliances and ensure safety.
...[Details]
Common ARM instructions 1: data processing instructions •Data transfer instructions mov mvn mov r1, r0 @Data transfer between two registers mov r1, #0xff @Assign the immediate value ...[Details]