AV 6 0 A D U A L O U T P U T H A L F - B R I C K P O W E R C O N V E R T E R S
3 6 V D C T O 7 5 V D C I N P U T, 7 5 WAT T O U T P U T
Introduction
AV60A dual output series provides two inde-
pendent and fully regulated positive outputs,
the outputs are also separately trimmable. A
remote on/off feature is included as standard.
AV60A dual output isolated DC/DC converters
is built using the industry standard half-brick
pin-out and package 61.0mm x 57.9mm x
Features
1. Two independent positive outputs
2. Each output is separately trimmable
3. CNT function
4. High efficiency
5. High power density
6. Low output noise
7. Metal baseplate
12.7mm (2.4" x 2.28" x 0.5"). Typical efficien-
8. Input undervoltage protection
cies are 82% for the 5V/3.3V outputs, and 80%
for the 3.3V/2.5V outputs. The AV60A dual out-
put series is available with 2:1 input range of
36V-75V, and with output combination of
5V/3.3V and 3.3V/2.5V at maximum current of
15 Amps. The maximum current can be drawn
from either output, or in any combination, as
long as the total output current does not exceed
15 Amps. The output power is 75W. The input-
output isolation is 1500Vdc.
AV60A dual output series is designed to meet
CISPR22, FCC Class A, UL, TUV, and CSA
certifications.
9. Short circuit protection
10. Over current protection
11. Output overvoltage protection
12. Wide operating
-40°C ~ 100°C
case
temperature:
TEL:
FAX:
USA
1-760-930-4600
1-760-930-0698
Europe
44-(0)1384-842-211
44-(0)1384-843-355
Asia
852-2437-9662
852-2402-4426
-2-
www.astec.com
AV 6 0 A D U A L O U T P U T H A L F - B R I C K P O W E R C O N V E R T E R S
3 6 V D C T O 7 5 V D C I N P U T, 7 5 WAT T O U T P U T
Typical Application
Fuse*
+Vin
CNT
+Vo2
-Vo2
C4
C5
Load2
Vin
C1
C6
CNT
CASE
Trim2
+Vo1
-Vo1
C2
C3
Load1
-Vin
Trim1
NOTE:
The figure is Positive Logic Control,
if the CNT pin is left open, the converter will default to “control
on” operation.
Negative Logic Control is also available.
Positive Logic Control:
Low=Off,
Negative Logic Control:
Low=On,
High=On.
High=Off.
Recommended External components:
Fuse* : Recommended: 3~4A.
C1 : Recommended 470
µ
F/100V.
C3=C5 : Recommended electrolytic capacitor of 470
µ
F/16V.
C2=C4 : Recommended metallitic film capacitor of 0.47
µ
F/16V.
C6 : Recommended 0.01
µ
F/1500V.
Block Diagram
+Vin
-Vin
1
EMI
Filter
2
OCP
5
4
+Vo1
-Vo1
To -Vin
Feed-
back
6
Trim1
+Vo2
-Vo2
Trim2
7
CNT
3
PWM
8
PWM
Error
AMP
9
TEL:
FAX:
USA
1-760-930-4600
1-760-930-0698
Europe
44-(0)1384-842-211
44-(0)1384-843-355
Asia
852-2437-9662
852-2402-4426
-3-
www.astec.com
AV 6 0 A D U A L O U T P U T H A L F - B R I C K P O W E R C O N V E R T E R S
3 6 V D C T O 7 5 V D C I N P U T, 7 5 WAT T O U T P U T
Ordering Information
Model
Number
Input
Voltage
(V)
48
Output
Voltage
(V)
5, 3.3
Output
Current
(A)
15, 15*
Ripple
(mV rms)
max
30
Noise
Efficiency
(mV pp)
(%)
max
min typ
150
80
82
82
79
AV60A-048L-033D025
48
3.3, 2.5
15, 15*
25
150
78
80
80
76
AV60A-048L-050D033N*
48
5, 3.3
15, 15*
30
150
80
82
82
79
AV60A-048L-033D025N*
48
3.3, 2.5
15, 15*
25
150
78
80
80
76
notes and conditions
AV60A-048L-050D033
Io1=15A, Io2=0A
Io1=7.5A, Io2=7.5A
Io1=1.5A, Io2=15A
Io1=15A, Io2=0A
Io1=7.5A, Io2=7.5A
Io1=1.5A, Io2=15A
Io1=15A, Io2=0A
Io1=7.5A, Io2=7.5A
Io1=1.5A, Io2=15A
Io1=15A, Io2=0A
Io1=7.5A, Io2=7.5A
Io1=1.5A, Io2=15A
Note: The maximum output current of auxiliary output Vo2 is 12A when the case temperature is between 80~100°C.
The products with suffix ‘N’ refer to the negative logic control products, default is positive logic control.
The products with suffix ‘-7’ refer to products with pin length of 5.8mm.
The products with suffix ‘-6’ refer to products with pin length of 3.8mm.
The products with suffix ‘-8’ refer to products with pin length of 2.8mm.
Default pin length is 4.8mm.
TEL:
FAX:
USA
1-760-930-4600
1-760-930-0698
Europe
44-(0)1384-842-211
44-(0)1384-843-355
Asia
852-2437-9662
852-2402-4426
-4-
www.astec.com
AV 6 0 A D U A L O U T P U T H A L F - B R I C K P O W E R C O N V E R T E R S
3 6 V D C T O 7 5 V D C I N P U T, 7 5 WAT T O U T P U T
Absolute Maximum Rating
Characteristic
Input Voltage(continuous)
Input Voltage(peak/surge)
Case temperature
storage temperature
Min
-0.3
-0.3
-40
-55
Typ
Max
80
100
100
125
Units
Vdc
Vdc
°C
°C
100ms non-repetitive
Notes
Input Characteristics
Characteristic
Input Voltage Range
Input Reflected Current
Turn-off Input Voltage
Turn-on Input Voltage
Turn On Time
Turn On Delay
30
31
33
34
5
10
Min
36
Typ
48
Max
75
200
35
36
Units
Vdc
mAp-p
V
V
ms
ms
Vin=48V, Io1=7.5A, Io2=7.5A
Io1=7.5A, Io2=7.5A
Io1=7.5A, Io2=7.5A
Notes
CNT Function
Characteristic
Logic High
Logic Low
Control Current
Min
5
0
Typ
Max
15
1.2
2
Units
Vdc
Vdc
mA
Notes
Reverse logic option available.
General Specifications
Characteristic
MTBF
Isolation
Pin solder temperature
Hand Soldering Time
Weight
Min
Typ
2300
1500
260
5
65
Max
Units
k Hrs
Vdc
°C
s
grams
wave solder < 15 s
iron temperature 425°C
Notes
Bellcore TR332, 25°C
TEL:
FAX:
USA
1-760-930-4600
1-760-930-0698
Europe
44-(0)1384-842-211
44-(0)1384-843-355
Asia
852-2437-9662
852-2402-4426
-5-
www.astec.com
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
