14-Pin SO (derate 8.3mW/°C above +70.......................667mW
Operating Temperature Range
Automotive Application...................................-40°C to +125°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
DD
= 5V, V
SS
= 0, V
CM
= 0, T
A
= -40°C to +125°C, unless otherwise noted. Typical values are at T
A
= +25°C.) (Note 1)
PARAMETER
Operating Voltage Range
Supply Current Per Comparator
Input Offset Voltage
Input Offset Voltage
Temperature Coefficient
Hysteresis
Input Bias Current
Input Offset Current
Common-Mode Voltage Range
Common-Mode Rejection Ratio
Power-Supply Rejection Ratio
I
BIAS
I
OS
V
CM
CMRR
PSRR
Guaranteed by CMRR test
V
SS
≤
V
CM
≤
(V
DD
- 1.1V), V
DD
= 5.5V
V
DD
= 2.5V to 5.5V
V
OH
= V
DD
- V
OUT,
(V
IN+
- V
IN-
)
≥
20mV
V
OL
= V
OUT
- V
SS,
(V
IN-
- V
IN+
)
≥
20mV
R
L
= 10kΩ,
C
L
= 15pF (Note 4)
R
L
= 10kΩ, C
L
= 15pF
C
L
No sustained oscillations
I
SOURCE
= 10µA
I
SOURCE
= 4mA
I
SINK
= 10µA
I
SINK
= 4mA
V
OD
= 10mV
V
OD
= 100mV
V
SS
70
60
100
80
2
160
2
180
50
8
3
20
150
150
400
mA
µs
ns
ns
pF
400
mV
SYMBOL
V
DD
I
DD
V
OS
TCV
OS
(Note 3)
(Note 2)
CONDITIONS
Guaranteed by PSRR test
MIN
2.5
2.8
±1
±1
4
3
±2
80
±60
V
DD
- 1.1
TYP
MAX
5.5
5
±8
UNITS
V
µA
mV
µV/°C
mV
nA
nA
V
dB
dB
Output-Voltage Swing
V
OL
, V
OH
Output Short-Circuit Current
Propagation Delay
Rise and Fall Time
Power-On Time
Maximum Capacitive Load
I
SC
t
pd+
, t
pd
-
t
R
, t
F
R
L
= 10kΩ, C
L
= 15pF (Note 5)
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
All devices are production tested at 25°C. All temperature limits are guaranteed by design.
Comparator Input Offset is defined as the center of the hysteresis zone.
Hysteresis is defined as the difference of the trip points required to change comparator output states.
V
OD
is the overdrive voltage beyond the offset and hysteresis-determined trip points.
Rise and fall times are measured between 10% and 90% at OUT.
I recently participated in the school's electronic design competition, the topic was a simple wind tunnel, but I don't have the knowledge, so I turned to the masters of this site to teach me how to de...
[align=left][color=rgb(34, 34, 34)][font="][size=4]The transistor collector DC circuit is the circuit between the collector and the DC working voltage terminal. This DC circuit is the circuit with the...
Important things to say in advance:
I would be satisfied if I could understand the data that is ultimately exposed to the air during a Bluetooth transmission, and then parse and understand it.
I searc...
Flower watering indicator
Author: Zhang Zezhong
Flowers are loved by everyone. Many people like to grow flowers. The flowers they just bought are gorgeous and colorful, but after a few days, the flowe...
How to understand the alarm performance of 14 or more half-cycles of arc faults in 1s in GB14287.4 "Electrical Fire Monitoring System Part 4: Arc Fault Detector"? How to understand the alarm performan...
With the improvement of economic level, cars are gradually becoming people's daily means of transportation. However, the electronic products that people carry with them, such as mobile phones, cann...[Details]
ACE intelligent traffic management solution creates a green, healthy and efficient urban traffic organic operation body. In recent years, with the continuous advancement of the strategy of build...[Details]
What is the difference between a vibrating rod level switch and a tuning fork level switch? This is a question that is often mentioned in forums and user consultations. Yes, both work based on the pr...[Details]
RS485 Communication Notes
1. How to
wire Good wiring can greatly reduce the impact of interference and improve the reliability of communication, but we often lack understanding of this in...[Details]
1 Introduction
LED lighting can easily provide rich and vivid colors, that is, the same bulb can give warm white light, cool white light or any color in the spectrum, which CFL lamps cannot ...[Details]
Usually, FPGA engineers have a headache when compiling large projects because the compilation time is very long, often taking several hours. If it is in the debugging stage, it takes seve...[Details]
According to foreign media reports, a Samsung smartphone with the model number "SM-A507FN" recently appeared in the GeekBench benchmark database. According to Samsung's previous naming rules, the mod...[Details]
In the past two years, global companies have experienced the baptism of the epidemic, and the way they view digital marketing has changed significantly from the past. Brand owners or consumers are ...[Details]
PrimeSense technology is the basis of the Microsoft Kinect sensor system, which is designed to work with the Microsoft Xbox 360 console gaming system (Figure 1). Its working principle is very simple,...[Details]
With the development of modern technology, electricity is becoming more and more closely related to our lives. From industrial production to every detail of home life, electricity is indispensable....[Details]
1. How to use an oscilloscope to test and analyze the reliability of a designed product?
A: Oscilloscopes have long been one of the most effective tools for testing electronic circuits. B...[Details]
(Wuhan) International New Energy Vehicle Industry Exhibition Time: November 25-27, 2021 Venue: Wuhan International Expo Center Smart cars, a shared future (Wuhan) International New Energy Vehic...[Details]
A spectrum analyzer is an instrument for studying the spectrum structure of electrical signals. It is used to measure signal parameters such as signal distortion, modulation, spectrum purity, frequen...[Details]
Circuit principle: The circuit is provided with +5V power supply voltage by transformer, diode and voltage regulator IC7805. The battery voltage is divided by resistors R5 and R6 and sent to the B...[Details]
High-voltage solid-state soft start cabinet is a device used for high-voltage motor starting. It controls the on and off of thyristors to achieve soft starting and soft stopping of motors, thereby ...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
