Altium Designer 19 DRC check, it is clearly connected but it still shows Un-Routed Net, and NetAntennae via

oyhprince

Altium Designer 19 DRC check, it is clearly connected but it still shows Un-Routed Net, and NetAntennae via [Copy link]

 

Please help me, the software is altium designer19

1 I am clearly connected, but why am I still seeing "Un-Routed Net Constraint: Net xxx Between Pad xxx"?

2

Net Antennae (Tolerance=0mil) (All)
Net Antennae: Via (95mil,-140mil) from Top Layer to Bottom Layer

qwqwqw2088

There should be a GND network that is not connected.

You can hide other layers first and only keep the top Layer

Zoom in and carefully check if there are any short thin wires that are not connected, such as the end or tail of the wire.

okhxyyo

There are thread heads, click to see more

oyhprince

qwqwqw2088 posted on 2020-6-21 21:30 There should be a GND network that is not connected. You can hide other layers first, leaving only the top Layer. Zoom in and check carefully to see if there are any thin short lines...

via What's up with the antenna?

qwqwqw2088

oyhprince posted on 2020-6-21 23:14 via What's up with the antenna?

Via is a hole on PCB, generally refers to metallized hole

qwqwqw2088

How, is it related to Kong?

Are there too many holes in the ground?

oyhprince

qwqwqw2088 posted on 2020-6-22 08:24 What, is it related to the holes? Are there too many holes in the ground?

There is only one GND via on the whole board. If you type the via, it will report an error.

qwqwqw2088

oyhprince posted on 2020-6-22 13:55 There is only one GND via in the whole board. As long as you type via, it will report an error

The ground is the GND network. It is estimated that there is a GND network at the bottom.

First remove the top copper layer.

oyhprince

The thread is too hard to find

If I check and the wires are connected, will it be okay to ignore the Un-Routed Net Constraint and print it out?

qwqwqw2088

oyhprince posted on 2020-6-22 17:17 The wire ends are too hard to find. If I check, the wires are already connected, ignore the Un-Routed Net Constraint &nb ...

Hard to say.

You can check if there is any wire leakage.

qwqwqw2088

Click reports---board information---report,
pull down the slider, select routing information,
and then click reports.
The board's wiring information will appear.

oyhprince

qwqwqw2088 posted on 2020-6-22 17:23 Click reports---board information---report, slide down the slider, select routing information, and then click reports. ...

There is no such option. I suspect that there is something wrong with my software cracking.

qwqwqw2088

oyhprince

qwqwqw2088 posted on 2020-6-22 17:46

In which menu is it? / Which version is your ad?

qwqwqw2088

oyhprince posted on 2020-6-22 17:52 In which menu is it? / Which version of your ad is it?

Which AD version has

oyhprince

qwqwqw2088 posted on 2020-6-22 17:55 Which AD version has it

How to call it out

qwqwqw2088

oyhprince posted on 2020-6-22 18:01 How to adjust it

oyhprince

qwqwqw2088 posted on 2020-6-22 23:15

There are no reports for AD19

qwqwqw2088

oyhprince posted on 2020-6-23 00:27 There are no reports of AD19

PCB blank area, F11, Properties tab, Board Information,,,,

qwqwqw2088

Open the PCB project, open ".PcbDoc", and the Properties panel on the right

Find the Properties panel

Scroll down and click Reports

Select routing information and click Report.