How to connect multimedia speakers_How to use multimedia speakers

How to connect multimedia speakers

1. Insert the red-wired mini speaker plug into the right channel red audio output jack of the main speaker (normally it is red on the right and white on the left).

2. Insert the plug of the white-wired small speaker into the white audio output jack of the left channel of the main speaker (normally it is red on the right and white on the left).

3. Then insert the red audio input plug of the connecting cable into the red audio input jack.

4. Then insert the white audio input plug of the connecting cable into the white audio input jack.

5. Finally, insert the black plug at the other end of the cable into the green jack on the back of the chassis, and the connection is complete.

How to use multimedia speakers

The instructions for using multimedia speakers of each brand will be slightly different

1. Audio input selection: An external audio cable is required to connect the audio source.

2. Turn the audio knob to the minimum position, turn on the power, and adjust the volume and other knobs as needed.

3. When inserting an SD card or USB flash drive, read the MP3 songs in the corresponding memory; the song status can be controlled by the PREV PLAY/PAUSE NEXT button.

4. When the SD card and USB flash drive are inserted, you can use the MODE button to switch between the SD card and USB flash drive/audio input port.

5. The LED status indicator light stays on in audio input status, flashes quickly when reading a USB flash drive or SD card, stays on when playing a song, and flashes slowly when paused.

How to use Edifier C2 multimedia speaker

Edifier C2 is a multimedia speaker under Edifier. Its affordable price and good sound quality make it a very high cost-effectiveness, which has attracted the attention of many users. However, some users don’t know much about the use of speakers. Next, the editor will bring you relevant setting tutorials.

1. Connect the audio source and speakers:

For specific connection methods, please refer to the speaker connection diagram

2. Sound emission

Plug in the power supply, turn on the power switch, the system enters the playback state, the amplifier remote control display window will jump from 0 to the system default master volume value 30; the working indicator aperture and PC input indicator light up, turn the volume adjustment knob to adjust the master volume, the adjustment range is between 0-60, 60 means the maximum volume, 0 means the minimum volume. In the playback state, press the "MUTE" button on the amplifier or remote control, the system is in mute state, the working indicator aperture and input indicator light go out, and the display window shows "--"; press the "MUTE" button again, the system resumes the playback state.

3. Audio source selection:

This system has two audio input ports, "PC" and "AUX". The system defaults to "PC" input when working. Press the "INPUT" button on the front panel of the amplifier to switch the system between the two input ports "PC" and "AUX". When switching the input port, the corresponding "PC" and "AUX" input indicators will also switch accordingly.

4. Volume adjustment instructions

When the "FUNCTION" key is pressed once in the playback state, the display window will display in a loop, one by one: "BASS" light is on, showing the ground volume value; "TREB" light is on, showing the treble volume value; "BASS" and "TREB" lights are off, showing the master volume value. It means that the system enters "bass fine-tuning", "treble fine-tuning" and resumes playback state respectively; the rotation is -7 to 7, negative numbers indicate volume attenuation, positive numbers indicate volume increase, and 0 is the system default value, indicating no increase or attenuation.

During the sub-volume adjustment process, if an incorrect operation is performed within 3 seconds, the system will return to the main volume adjustment state, and the display window will show the current main volume value.

5. Instructions for using the headphone jack

When using headphones to enjoy music, you need to insert the 3.5mm stereo plug on the headphones into the headphone jack on the front panel of the amplifier; after correct connection, the sound of each speaker disappears, the working indicator light goes out, and the display window shows the master volume value; at this time, the system can still control the headphone volume.