Note: The serial line must be in full state
2.
3.
4.
★
★
★
★
★
★
5.
★
There are three reasons:
(Ⅰ) The serial port line is a three-wire system
(II) The short-circuit cap of J1 or J2 is not added
(III) The mainboard is not powered on
★
The CPU model selected in FlashMagic is inconsistent with the CPU model of the target board
Previous article：Cortex-M3 Learning Log (I) -- GPIO Experiment 1
Next article：LPC1768-Cortex-M3 Learning Log--UART0 Experiment
- Popular Resources
- Popular amplifiers
LF411MH/883C- Download from the Internet--ARM Getting Started NotesA brief introduction: From today on, the ARM notebook of the rookie is open, and it can be regarded as a place to store these notes. Why publish it? Maybe you are interested in it. In fact, the reason for these notes is ...
- Learn ARM development(22)Turning off and on interrupts Interrupts are an efficient dialogue mechanism, but sometimes you don't want to interrupt the program while it is running. For example, when you are printing something, the program suddenly interrupts and another ...
- Learn ARM development(21)First, declare the task pointer, because it will be used later. Task pointer volatile TASK_TCB* volatile g_pCurrentTask = NULL;volatile TASK_TCB* vol ...
- Learn ARM development(20)With the previous Tick interrupt, the basic task switching conditions are ready. However, this "easterly" is also difficult to understand. Only through continuous practice can we understand it. ...
- Learn ARM development(19)After many days of hard work, I finally got the interrupt working. But in order to allow RTOS to use timer interrupts, what kind of interrupts can be implemented in S3C44B0? There are two methods in S3C44B0. ...
- Learn ARM development(14)
- Learn ARM development(15)
- Learn ARM development(16)
- Learn ARM development(17)
Professor at Beihang University, dedicated to promoting microcontrollers and embedded systems for over 20 years.
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
- Huawei's Strategic Department Director Gai Gang: The cumulative installed base of open source Euler operating system exceeds 10 million sets
- Download from the Internet--ARM Getting Started Notes
- Learn ARM development(22)
- Learn ARM development(21)
- Learn ARM development(20)
- Learn ARM development(19)
- Learn ARM development(14)
- Learn ARM development(15)
- Analysis of the application of several common contact parts in high-voltage connectors of new energy vehicles
- Wiring harness durability test and contact voltage drop test method
- EEWORLD University Hall ---- Lao Wu's MCU Practice_NO.1 Project Practice
- [NXP Rapid IoT Review] + Rapid IoT Studio online IDE
- I'm studying BQ76940 recently and want to develop a BMS. I've been looking for information and encountered some questions during the process.
- [Sipeed LicheeRV 86 Panel Review] 4. Building a cross-compilation environment
- [Speech and vision module based on ESP32S3] Software development progress - ESP32S3 JPEG encoding performance test
- 【GD32E231 DIY Contest】4. Achieve 60-second timing
- 【DIY Creative LED V2】V2 version
- How to analyze the role of this diode in the MOS tube perfusion circuit?
- [RVB2601 Creative Application Development] Unboxing and Getting Started
- FPGA_100 Days Journey_2-choose-one data selector.pdf
京公网安备 11010802033920号