Quality identification of LED unit boards-EEWORLD

Collect

The quality of LED display unit board can be identified from the following aspects:

1. Check the appearance quality of the selected material

①PCB board material and processing quality;

②IC device brand and consistency;

③Quality of luminous dot matrix;

2. Check the circuit design specifications and PCB wiring to meet the LED display technology requirements;

3. Check welding quality

Check whether there are any missing or wrong components on the patch, and whether there are any burrs or short circuits on the component pins. Check whether the direct plug-in solder joints are smooth and round, and whether the board surface is clean and tidy, without any false solder joints or leaks. Check the flatness of the light-emitting dot matrix and the consistency of the ink color.

4. Power-on test (refer to the steps in the "Performance Test Report")

①Power on to test the consistency of the luminous dot matrix;

②Power on to test whether the row driver tube CEM4953 is effectively protected;

③Power on to test signal transmission capability;

Keywords：LED Reference address：Quality identification of LED unit boards

Previous article：LED display: P10-1R module principle and maintenance
Next article：Dual-color LED display scanning method

Recommended ReadingLatest update time:2024-11-17 00:39

Advantages and disadvantages of LCD TV_Which is better, LCD TV or LED TV

Advantages and Disadvantages of LCD TVs advantage: Lightweight and portable Traditional monitors use CRT, which must emit electron beams to the screen through an electron gun. Therefore, the tube neck of the tube cannot be made very short. When the screen size is increased, the volume of the ent

[Embedded]

Heat dissipation design for high-power LEDs

In recent years, high-power LEDs have developed rapidly, with great improvements in structure and performance, increased production and reduced prices. Ultra-high-power white LEDs with a single power of 100W have also been developed. Compared with previous years, there has been great progress in luminous efficiency.

[Power Management]

Heat dissipation design for high-power LEDs

Using Delay to Realize LED Flowing Light of PIC Microcontroller

Using Delay to Realize LED Flowing Light Using PIC Single Chip Microcomputer ;**************************************************** __CONFIG 3F39H; Set the oscillation mode in the configuration bit to XT, and disable or turn off all others ;******************************************************** status equ 3h ;

[Microcontroller]

Design considerations for LED driver power supplies

LED power driver is a voltage converter that converts power supply into a specific voltage and current to drive LED to emit light. Usually, the input of LED driver power includes high-voltage power frequency AC (i.e. mains), low-voltage DC, high-voltage DC, low-voltage high-frequency AC (such as the output of elect

[Power Management]

High-power LED heat dissipation will adopt active cooling solutions

As we all know, one of the advantages of LED is that it has a high photoelectric conversion efficiency, which is a great improvement compared with traditional light sources. However, due to the limitations of current technological development, the efficiency is still only about 15-20%, which means that up to 80-85%

[Power Management]

How to use microcontroller LED light-emitting diode to display "love"

1. Hardware diagram 2. Components list 4. Procedure (reference) #include reg51.h void delay(unsigned int k); void main() { unsigned char i,j,h,y,w,e,t,s; while(1) { w=0x80; e=0x01; t=0x00; s=0xff; for(i=0;i 3;i++) { if (i 1) { for (j=0;j 8;j++) { P1=w; P3=t; w =1; delay(200); } } else if

[Microcontroller]

STM32F103 LED light simple program implementation

1. Create a configuration library file for the project 2. Write main.c code else GPIO_SetBits(leds_gpio .group, leds_gpio .pin); } void Delay(__IO uint32_t nCount) { for(; nCount != 0; nCount--) ; } int main(void) { /* Initialize system clock */ SystemInit();

[Microcontroller]

Ultra-thin LED backlight implementation solution

introduction Backlight sources are divided into direct-lit backlight sources and edge-lit backlight sources according to the position of the light source. In direct-lit backlight sources, the LED light source is placed directly below the light-emitting surface. The light emitted by the light source is diffuse

[Power Management]

Ultra-thin LED backlight implementation solution

Popular Resources
Popular amplifiers