During the production process of semi-finished and finished products of power transformers, before the newly installed transformers are put into operation, and according to the preventive test procedures of the State Grid, it is required to regularly test the turns ratio or voltage ratio of the operating transformers. The traditional ratio bridge is cumbersome to operate, the readings are not intuitive, and necessary conversions must be performed. The test result is only the value of one phase ratio. This TKBB transformer ratio tester overcomes the shortcomings of traditional ratio bridge testing. The screen uses a large-screen high-resolution LCD display, which is convenient for on-site use. It has a Chinese menu prompt function, is easy and intuitive to operate, and completes the three-phase ratio test at one time. The test speed is fast and the accuracy is high.
Transformation ratio group tester function
1 Full three-phase sinusoidal inverter power output, automatic output voltage adjustment, with soft start and soft stop functions, so the test speed is fast and the accuracy is high.
2 Three-phase transformer, single-phase transformer, PT, Z-type transformer ratio, group, polarity test function.
3 It has a blind test function, that is, it can perform ratio and group tests when the high and low voltage connection methods are unknown.
4 CT ratio polarity test function.
5. It has the function of angle difference test during single-phase test.
6 The maximum tapping position can be tested is 197.
7. Wide test range, up to 10000.
8. High and low voltage reverse connection protection function.
9 Output short circuit protection function.
10. Clock and date display without power failure; data storage methods include local storage and USB storage, where the local storage can store 500 test data, and the local storage can be transferred to the USB flash drive; the data format of the USB flash drive is Word format, which can be directly edited and printed on the computer.
11 Thermal printer printing function, fast and silent.
12 Small size, light weight, easy to carry and use.
Previous article:Operating steps and precautions of the fully automatic fabric air permeability tester
Next article:How to use the positive connection method of the dielectric loss transformer dielectric loss tester
Recommended ReadingLatest update time:2024-11-16 23:47
- Keysight Technologies Helps Samsung Electronics Successfully Validate FiRa® 2.0 Safe Distance Measurement Test Case
- From probes to power supplies, Tektronix is leading the way in comprehensive innovation in power electronics testing
- Seizing the Opportunities in the Chinese Application Market: NI's Challenges and Answers
- Tektronix Launches Breakthrough Power Measurement Tools to Accelerate Innovation as Global Electrification Accelerates
- Not all oscilloscopes are created equal: Why ADCs and low noise floor matter
- Enable TekHSI high-speed interface function to accelerate the remote transmission of waveform data
- How to measure the quality of soft start thyristor
- How to use a multimeter to judge whether a soft starter is good or bad
- What are the advantages and disadvantages of non-contact temperature sensors?
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
- Power Development Tutorial: Summary of topology transformation calculation formulas
- Switching Power Supply Interest Group 15th Task
- Omron E6A2
- ADI Think Tank Secrets New Release丨High Speed Circuit Design Guide is now available for download
- 【LAUNCHXL-CC1350-4】- 1: Install CCS on Ubuntu 20.04
- Is there any circuit with PWM input and 0-10V output? The RC filtering solution is not fast enough.
- Today’s live broadcast: Infineon’s system solutions make electric motorcycle design more reliable and efficient!
- [ESP32-S2-Kaluga-1 Review] MQTT component connection to OneNet
- Review summary: RTT & Renesas high-performance CPK-RA6M4 development board
- Two methods of chip unpacking