The application of DISTO in mines mainly utilizes the combination of DISTO and domestic theodolites to form a prismless semi-station, which is used in underground mining areas to measure point positions, cross-section heights, mining area volumes, etc.
Before a certain unit purchased the DISTO handheld distance meter, what was the original underground measurement method? According to a person in charge of the measurement unit, they used a theodolite, a tape measure, a fishing rod, and a domestic pulse distance meter to measure the underground mining area. The main disadvantages of this method are:
1. Low measurement accuracy. There is a set of data to prove this: at the end of 1998, two surveying teams jointly measured the volume of a stope. The result was 55,000 cubic meters for one team and 68,000 cubic meters for the other team. The measurement values varied greatly after each measurement, so they dared not continue to measure.
2. Slow speed and low efficiency. The working environment underground cannot be compared with the ground environment. Due to the poor underground conditions, dim light, low safety factor and other limitations, the measurement speed is very slow and the efficiency is very low. Often, one measurement point takes several times more than the usual measurement time.
3. Although domestic pulse handheld rangefinders can also measure distances, people cannot see the location of the target point because it uses ultrasonic ranging. In addition, the measuring range is too short and the accuracy is low, which greatly limits its scope of use.
Changes after using DISTO:
In underground measurement, the surveyor only needs to set up a theodolite and a rangefinder, and there is no need for people to stand at the target point. The measurement task can be completed smoothly, comprehensively and relatively accurately in a short time, overcoming the previous shortcomings of slow speed, low efficiency and poor accuracy. In particular, the advantage of the handheld laser rangefinder in underground measurement that the red laser point can be seen is particularly praised by the surveyor. In underground measurement, the handheld laser rangefinder can also be used alone, which is quite convenient. It can also store a large amount of measurement data without the need for underground measurement records. In addition to being convenient for use underground, the handheld laser rangefinder can also be used for open-pit slope measurement and layout.
Previous article:What are the uses of chromatograph?
Next article:What is Optical Time Domain Reflectometry?
- Popular Resources
- Popular amplifiers
- Keysight Technologies Helps Samsung Electronics Successfully Validate FiRa® 2.0 Safe Distance Measurement Test Case
- From probes to power supplies, Tektronix is leading the way in comprehensive innovation in power electronics testing
- Seizing the Opportunities in the Chinese Application Market: NI's Challenges and Answers
- Tektronix Launches Breakthrough Power Measurement Tools to Accelerate Innovation as Global Electrification Accelerates
- Not all oscilloscopes are created equal: Why ADCs and low noise floor matter
- Enable TekHSI high-speed interface function to accelerate the remote transmission of waveform data
- How to measure the quality of soft start thyristor
- How to use a multimeter to judge whether a soft starter is good or bad
- What are the advantages and disadvantages of non-contact temperature sensors?
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
- Keysight Technologies Helps Samsung Electronics Successfully Validate FiRa® 2.0 Safe Distance Measurement Test Case
- Innovation is not limited to Meizhi, Welling will appear at the 2024 China Home Appliance Technology Conference
- Innovation is not limited to Meizhi, Welling will appear at the 2024 China Home Appliance Technology Conference
- Huawei's Strategic Department Director Gai Gang: The cumulative installed base of open source Euler operating system exceeds 10 million sets
- Download from the Internet--ARM Getting Started Notes
- Learn ARM development(22)
- Learn ARM development(21)
- Learn ARM development(20)
- Learn ARM development(19)
- Learn ARM development(14)
- 【GD32F310G-START】SPI driver ST7735
- Clock Generator MS5351M
- What are the applications of ultrasonic transducers? Medical atomizer-power amplifier case
- Does anyone know the standards for embedded OS? What does it mean that RTthread has passed GJB7718-2012 and GJB7706-2012?
- stm32 remote upgrade
- MOS model recommendation
- High-end DEBUG often only requires the simplest testing methods
- Why are the calculation results of Matlab and the microcontroller so different?
- Can you guys help me see if this is reasonable? I have checked and there is no problem, but I am still asking.
- How to use thermistor and 8051 single chip and LCD to display temperature detection. Please answer