Journal article: An advanced autofocus system for video camera using QUASI CONDITION REASONING

Recommended ContentMore

Open source project More

• AWTRIX 2.0 Bluetooth Music Edition
• smallest system
• 3.7V lithium battery charging module-TP4056
• daplink_v2
• Bluetooth power amplifier M18 Bluetooth + TPA3116 power amplifier
• Distinguished USB cement resistor dummy load
• 400VDC input, 28V/9A output, compact high-efficiency CLL resonant converter reference design
• AM signal processing experimental circuit
• Ink screen driver board
• #the4thLichuangcompetition#Small PLC output IO port expansion

Searched by Users

• 1. Illustrated Practical Electronic Technology Series: 100 Examples of OP Amplifier Application Techniques.pdf
• ADF435x series register quick configuration fool software
• STM32L0 Datasheet_DATASHEET_DM00108219
• The complete set of CAN bus in ISO-11898
• PCB Calculator
• C++ library function help documentation
• STC12C5A60S2 Chinese manual complete version
• Signal Integrity Analysis Software-HyperLynx Getting Started Guide (Chinese Version)
• Introduction and practice of robot Python geek programming
• Discrete-Time Signal Processing (Oppenheim 2nd Edition)

Just Take a LookMore

• TLP3547 Evaluation Board Evaluation Report
  [i=s]This post was last edited by MrKingMCU on 2018-10-12 19:33[/i] Test equipment: GW Instek desktop power supply PPE-3323 Fluke multimeter 15B+ The test items are mainly the parameters of the LED Te
• Drive Operating System
  I am a novice and basically have no knowledge of motor control. Here is a question for the experts: Do drivers with high control accuracy requirements usually have operating systems? Do drivers that c
• Disassemble the ATX power supply to see the pros and cons
  It is not an exaggeration to describe the power supply on the market today as "suddenly, a spring breeze comes, and thousands of pear trees bloom". What choice should we make in the face of these blos
• [Vicor White Paper Recommendation] Power Averaging Design Method with Voltage Regulation: Ideal Power Supply Solution for Pulse Loads
  What would you do when designing a pulse load power supply? What would happen if the pulse load device is designed based on the peak power only? Power expert Vicor: It is important to note that the pe
• How to use C language to find the corresponding value in the table in the microcontroller
  [size=4]The first one is the table lookup method[/size] [size=4] [/size] [size=4]For example, I have three data[/size] [size=4] [/size] [size=4]char code table={0x01, 0x02, 0x03} corresponding to 0xa,
• Share a book: Crazy STM32 practical lectures
• Design and implementation of Ethernet MII interface expansion based on FPGA
• [RISC-V MCU CH32V103 Review] Board Unboxing and Schematic Analysis
• Efficiency Programming of Single Chip Microcomputer Active Buzzer Driver
• The speed measurement scheme of motor compressor based on Labview

Trending Downloads

• Yaskawa Servo Drive Instructions 11
• MTK introductory training and internal schematics
• CAN bus message mechanism
• STM32 Firmware Library User Manual_v3.5
• Software DMA Implementation
• Can-bus introduction article for beginers
• Three-State Gain Controlled Monolithic Low Noise Amplifier
• Mechanism of Transmission Line Transformer and Design of Broadband Impedance Matching
• DS9092/DS9092L,pdf,datasheet (iButton Probe with LED)
• 1. Ability to conveniently manage multiple votes of different types on multiple pages; 2. Rich voting types

Trending ArticlesMore

• Amplifier input impedance parameters and application simulation
• Run, wireless charging!
• Did Intel really lose?
• [Chongqing Station] Registration for Melexis Sensing Technology Tour Seminar is now open!
• common problem
• Apple's most ambitious chip plan yet
• Summary of the Semiconductor Equipment Market in 2020
• ​ADI & Shijian will help you understand chemical analysis and analytical instrument application solutions. Answer questions and win prizes!