How to set up a safe lithium battery protection circuit

Recommended ContentMore

Open source project More

• NB-IOT module EA01
• #TheSeventhLichuangElectronic Competition#NSLink
• DI-152 - 3W, ultra-wide range input power supply for industrial applications
• J-LINK beggar version stm32f103c8t6 domestic core available
• Demo_NAE12S20
• EVSPIN32F0601S3 three-phase inverter based on STSPIN32F0601 3-shunt topology
• STM32F412 core board-v1.1
• Yadi electric vehicle charger (high label)
• RDA6625e 868/915MHz power amplifier Demo
• USB2.0-HUB-1

Searched by Users

• U disk Dos installation and boot files (DOS+Grud for self-made bootable U disk)
• Data Structures in Embedded System Software Design (Full Version)
• Drone flight control pixhawk schematic diagram
• An old brand of UCDOS Chinese operating system, you can use it directly after unlocking C:.
• VDA5 3rd 2021 Measurement and Inspection Processes
• UFIDA U8 financial software VB source code, this version is the 2002 version
• Renesas MCU Download Software
• BIOS source code for AMI motherboard.
• 100 Examples of Microwave RF Circuit Design and Simulation
• A collection of various programs for RS485 (serial port) communication based on single-chip microcomputer [C language]

Just Take a LookMore

• Hiring embedded software engineer
  Headhunting position [Hangzhou] Job responsibilities: 1. Responsible for the software design and debugging of the company's embedded products; 2. Cooperate with hardware engineers to conduct system te
• How to deal with idle pins in CMOS circuits
  [align=left][color=rgb(34, 34, 34)][font="]Since CMOS circuits have extremely high input impedance, they are very likely to sense interference voltages and cause logical confusion or even damage. Ther
• Ask everyone a question about chip manufacturing
  I read some "basic circuits" in a book, and many of them require "good" parameter consistency. I want to ask, since transistors and diodes look similar nowadays, are the parameters similar? Can I use
• RE radiation disturbance problem
  I have a question. I am currently working on a project. The laboratory tested RE (radiated interference) and found that the power exceeded the standard, ranging from 30M to 1Ghz. This project has WIFI
• Teach you how to control EMI in PCB design?
  [align=left][color=rgb(63, 63, 63)][font=Helvetica, Arial, "]With the improvement of IC device integration, the gradual miniaturization of equipment and the increasing speed of devices, the EMI proble
• 【Repost】The definition and difference between passive and active signals of sensors
• TI C64x+ DSP CACHE consistency analysis and maintenance
• Some basic knowledge about SPI-Flash
• Is your phone ready for 5G?
• Rare earth giant magnetostrictive transducer inverter power supply based on DSP chip TMS320F2812

Trending Downloads

• ics9170-07
• 5V1A Application Manual EMI.pdf
• 《Grounds for Grounding A Circuit to System Handbook》-Elya B. Joffe-Wiley-2010.
• AP20N03P
• VHDL PPT Tutorial
• Switch and relay selection
• Design of multi-point temperature monitoring system based on single bus
• Journal article: Sudden changes in the amount of cultivated land in China and their driving mechanisms
• General Considerations for Switching Power Supply Design
• Analysis of mainstream solutions for mobile phone charging circuits

Trending ArticlesMore

• The CPU is "stuck". Can the new track domestic GPU be adopted?
• Charging Extra | Make life "wireless" possible
• Dialog Mobile TV SoC Products
• Competition report | 24-hour Hackathon challenge is in full swing!
• Samsung gives up acquisition? NXP CEO and CFO both reduce their holdings!
• 2015 Google I/O Conference: New generation of Chromebooks made in China revealed
• The US makes things difficult for Huawei, but Taiwan's semiconductor companies benefit
• Selection of the latest chip product technology content
• Breaking News | Infineon Technologies Announces Latest Investment Plan in China at the CIIE
• Analyst: China's semiconductor industry self-sufficiency process is accelerating