RT9288A pdf datasheet (PWM Step-Up DC/DC Controller for White-LED Driver)

Recommended ContentMore

Open source project More

• Offline voice car
• STC8H1K08 development board
• cdsj relay
• Commonly used 4-string lithium battery protection board design information
• 75 W CNC Constant Current LED Driver Reference Design
• Xiaoxi->Motor driver MX1508 solution
• AP0100AT2L00XUGAH3-GEVB: 1 MP BGA coprocessor HB
• # Fifth Lichuang Electronic Design Competition #Modular-NOW
• NCP3063SMDBCKEVB: Surface Mount Buck Regulator Evaluation Board
• Brushless DC motor driver board QC-DRV-NN_V1.0

Searched by Users

• Vietnamese font, free
• U disk Dos installation and boot files (DOS+Grud for self-made bootable U disk)
• Optimization method and its MATLAB implementation (Xu Guogen)
• PCB package library download
• Run under dos, written according to the national standard GB-3321 short-circuit current calculation method
• Renesas MCU Download Software
• A point-based audio processing program developed based on ADSP21489 and the matching AD1939, integrating key and interrupt control
• Design specification for automatic fire alarm system GB 50116-98
• VSPD 6.9 virtual serial port cracked version
• Application of magnetic beads in EMC design of switching power supply

Just Take a LookMore

• Please help analyze this circuit.
  See a battery switching circuit, as shown below, 1. Q1 and Q2 are NMOS tubes, Q3, Q4 and Q5 are PMOS tubes, and D1 is a diode. 2. BAT1 and BAT2 are batteries. The capacity of BAT2 is larger than that
• kicad-eda_6-layer-pcb_A64-OlinuXino_Rev_D
• The wheel speed pulse signal of the car is too narrow, and the sampling frequency of the equipment is too low to collect it. Is there any way to extend the pulse width?
  This pulse signal is only 0.08ms. It is too short.
• Battery Test Equipment --- Signal Chain
  Stanley I With the rise of the lithium battery industry, the market for battery testing equipment has also become huge, and it is mainly used in the capacity division of 3C batteries and power batteri
• iTOP-4418 development board TF card burning-boot uboot
  Connect the TF card to the development board, set the DIP switch to TF card boot, and enter the uboot mode, as shown in the figure below.As shown in the figure below, use the command "fastboot" and th
• LSM6DSL cannot generate interrupts, WAKE_UP_SRC is always 0; changing CTRL1_XL doubles the Z-axis reading
• MSP432 learning experience: system tick timer
• Introduce the factors to be considered in selecting DSP chips with examples
• Tektronix Industrial Application Standard and High-Speed Interface Test Solutions
• Ora Good Cat “chip replacement incident”: How big is the gap between the two chips?

Trending Downloads

• Design of DeviceNet Interface Circuit in Industrial Temperature Control System
• Music phone based on MTK (codec circuit)
• DSP5410 controls AD50 for digital recording experiment
• Mobile Phone Design Company Industry Report
• Design of liquid level data acquisition and transmission system based on CAN bus
• Design of Cyclic Redundancy Check Module Based on FPGA
• Brief Introduction of Putian TD-SCDMA HSDPA Technology
• CAN bus interface circuit design considerations
• Data Acquisition Toolbox 2.8
• Program for single chip microcomputer 51 to control hard disk

Trending ArticlesMore

• OnePlus 8 series: Visible excellence
• Pre-registration for the live broadcast with prizes | Unlock the black technology of automotive electronics and create a new realm of future driving
• [Jindian Atomic Urgent Recruitment] There are more than ten positions including embedded engineer + technical support + lecturer. Welcome to join Punctual Atomic.
• All the AR features of Samsung S9 are here. Do you think it looks like iPhone X?
• Tutorial | Make up this lesson: The principle of Bitcoin
• Qorvo's leading RF solutions
• Wages for AI professionals fall in the US
• Power semiconductor manufacturers should seize the opportunity of the rise of new materials