SCAN25100,pdf datasheet (2457.6, 1228.8, and 614.4 Mbps CPRI SerDes)

Recommended ContentMore

Open source project More

• 2kW Fully Digital Switch Mode AC-DC Converter Evaluation Board
• USB-HUB
• RGB light design
• heart shaped water lamp
• #FirstLichuangcompetition#Electronic smoking cessation box
• 40% programmable conventional configuration keyboard, a good choice for beginners
• [Changshu Institute of Technology] Differential amplifier circuit tester
• SW3519
• ATMEGA128 development board
• 12 V, 150 W power supply (based on STNRG011 digital combination and SRK2001 adaptive synchronous rectifier controller)

Searched by Users

• C51 reads GPS and communicates with the radio source code
• ARM assembly manual Chinese version
• 128-bit 2D barcode generator, tested and fully applicable to practical
• Practical RF Test and Measurement-Zhu Hui
• Danfoss VLT2900 inverter Chinese operation manual (MG29A341)
• Allwinner H3 Data Sheet
• Head First Design Patterns (Chinese scanned version).pdf
• DFI 4.0 Protocol
• Power Engineering DC System Design Handbook
• Renesas MCU Download Software

Just Take a LookMore

• [Liquid Level Sensor Evaluation] LED Liquid Level Indicator
  [i=s]This post was last edited by jinglixixi on 2021-9-8 23:48[/i]In addition to using digital tubes to display the value of analog quantities, it is more intuitive to use LED modules to indicate the
• Power module source knowledge you will understand after reading it - leakage inductance
  [size=20px]What is leakage inductance? [/size][align=left][color=rgb(51, 51, 51)]Leakage inductance is the part of magnetic flux that is lost during the coupling process between the primary and second
• Intelligent Temperature Controller Based on FPGA
• Evaluation report summary: New version of Zhongke Bluexun AB32VG1 RISC-V development board
  Event details: [New version of Zhongke Bluexun AB32VG1 RISC-V development board] Review | [New version of Zhongke Bluexun AB32VG1 RISC-V development board] Free trial_Electronic Engineering World (eew
• How to understand these four statements in STM32F103RCT6? The return statement should be declared before the main function, right?
  How do you understand these four statements in STM32F103RCT6? The return statement should be declared before the main function, right? Otherwise, I don't know what it means. I think this is much more
• MSP430 JTAG interface and BSW interface
• NXP launches new MCX series, high performance with NPU, to replace LPC and Kinetis?
• Chapter 5: Reading DHT12 data
• Share the disassembly of IPP-5002
• [Raspberry Pi Pico Review] --- Getting Started

Trending Downloads

• Class code for cluster reduction
• USB port communication: The upper computer and the lower computer can communicate through the USB port
• High Gain K-Band MMIC Low Noise Amplifier
• Centrifugal pump handout ppt
• NO1: \"The Way to Practice the Linux Kernel\" Essence Edition Methodology (Full Version).rar
• Graduate Teaching Book - Nonlinear Control System Theory and Application (2nd Edition) - Hu Yueming - National Defense Industry Press - 2005
• Development of a multi-step two-phase hybrid stepping motor driver
• A good compilation tool
• SD2200 clock data
• Isolation technology applied to reliable industrial measurement

Trending ArticlesMore

• The world's lowest power consumption WiFi RKi6000 smart product debuts at MWC
• Core Course | Analyzing how ICV LVS Explorer can accelerate full-chip LVS convergence
• Do you need a high voltage, high efficiency positive to negative converter?
• How 3D Hall Effect Sensors Enable Precise Real-Time Position Control in Autonomous Systems
• The low-key LoRa has another big move!
• Useful information | Understanding analog signals in PCB
• Learn about PI's new PowiGaN switching power supply IC and answer questions to win prizes!
• Sony's latest sensor and the technology behind it
• These movies may not win an Oscar, but they will give you a blast!