Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
I would like to ask how to download the executable file from the PC to the development board. I installed minicom and ftp server on Ubuntu under the PC, but I don’t know how to connect to the developm...
The camshaft position sensor is also called the camshaft angle sensor, phase sensor, cylinder identification sensor, and some cars also call it the 1 cylinder top dead center sensor. The most common n...
FX3/CX3 (CYUSB3065) Regarding the thread being locked:I use this chip, and then use the routine to create a DMA to transfer UVC video data through USB3 (as a computer camera). The function has been re...
I succeeded in using external interrupt PC2, but PC3 failed to use external interrupt function. I tried the external input reading function of PC3 and it worked. Does PC3 have any special configuratio...
With the global popularization and advancement of cellular wireless communication technologies represented by 4G and 5G, and the vigorous development of communication technologies in various professio...
The development of high-end electronic components urgently needs a breakthrough 2006-7-12 At present, my country's electronic transformer/inductor products are still mainly at the medium and low leve...
Cristiano Amon, president of Qualcomm, said in an interview with Xinhua News Agency during the Qualcomm Snapdragon Technology Summit held in Hawaii, the United States: " China's 5G scale will lead th...[Details]
1. Apparent variable conflict In the program, there is a global variable assigned gUI = 0x0A; but it is found that gUI does not get this value, but another global variable located at the first addre...[Details]
Spider-Man is a very popular IP image. In previous Marvel movies, he has a wide fan base. This time, Realme took advantage of the momentum to cooperate with the movie and launched a customized ...[Details]
NS-6 type experiment board drives stepper motor
The control output is P1 port
PH266-E1.2 is driven by 8050 and 8550 as power output. Press K1 key, the motor will accelerate from slow to fast and ...[Details]
Autonomous driving has huge potential, and the semiconductor industry represented by chips will benefit from it. Favorable policies and technological progress have accelerated the industrialization o...[Details]
Employees of the Parkhol Eisenstadt in Burgenland, Austria, recently welcomed five special new colleagues - Ketty, Hola, Bella, Flash and cleaning robot CC1. These five robots are the first batch o...[Details]
Host environment: Windows 7 SP1 Development environment: MDK5.14 Target board: STM32F103C8T6 Development library: STM32F1Cube library and STM32_USB_Device_Library The STM32Cube library provides som...[Details]
The correct use of thermocouples can not only accurately obtain the temperature value and ensure the product quality, but also save the material consumption of thermocouples, saving money and ensuring...[Details]
/**********************************************/
//This is our control of the steering gear
//Next we will use it by PI control;
//Date: 2013/5/15
/****************** *****************************...[Details]
At the Huawei MatePad and All-Scenario Conference in Shanghai, Huawei Consumer Business CEO Richard Yu said that Huawei Consumer Business will not enter the home appliance field in the future. He als...[Details]
AMD previously announced the latest Ryzen 3000 platform BIOS plan . The new version of AGESA 1.0.0.4 will further optimize the CPU acceleration frequency. Now MSI has officially announced its ...[Details]
The control chip is the commonly used HD61202 column driver and HD61203 row driver.
A Chinese character is composed of 16*16 pixels.
The scanning order is up and down, then to the se...[Details]
On November 8, 2022, MediaTek released the Dimensity 9200 flagship 5G mobile chip. With innovative breakthroughs in high performance, high energy efficiency, and low power consumption, and with a...[Details]
After appearing on the Wi-Fi Certification Alliance a few weeks ago, a new foldable phone with model number "SM-F415" appeared on Samsung India's official website, indicating that the phone wi...[Details]
On October 14, Yancheng City held the seventh press conference of the series of themed press conferences of "Carbon Road Pioneer" to further deepen reform and bravely develop new quality productivity....[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
