EEWORLDEEWORLDEEWORLD

Part Number

Search

MCR18EZHFX45R3

Description
Fixed Resistor, Metal Glaze/thick Film, 0.25W, 45.3ohm, 200V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 1206, CHIP
CategoryPassive components    The resistor   
File Size195KB,3 Pages
ManufacturerROHM Semiconductor
Websitehttps://www.rohm.com/
Environmental Compliance  
Download Datasheet Parametric View All

MCR18EZHFX45R3 Overview

Fixed Resistor, Metal Glaze/thick Film, 0.25W, 45.3ohm, 200V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 1206, CHIP

MCR18EZHFX45R3 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1922080345
package instruction, 1206
Reach Compliance Codecompliant
JESD-609 codee3
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTR, PAPER, 7 INCH
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance45.3 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceTin (Sn) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance1%
Operating Voltage200 V
Why is there no sound after the voice IC is connected to the power amplifier circuit?
Please help me find out what is wrong with the circuit. The speaker can play sound when it is directly connected to the voice IC, but there is no sound after it is connected to the power amplifier. Th...
吃星星的狼 Analog electronics
I'm a newbie, please KP
As shown in the picture above, I don’t understand...
小白求科普 Analog electronics
Use the MP3 decoding library provided by ST
Hardware platform: STM32F746G-DISC Development platform: KEIL_5.29 I will not introduce the detailed structure of MP3 files here , but only introduce how to use the MP3 decoding library. If you need t...
ilovefengshulin stm32/stm8
How do I design a circuit with such input and output?
1. There are signals in and out, and there may be a clk. When in changes from low level to high level, out should output high level immediately. No matter how in pin changes, out should not change. Ho...
littleshrimp FPGA/CPLD
Board burning problem
Every time the program of the board is changed, the board must be powered off, then powered on again, and the program must be burned again before it can run. This is inconvenient. Are there any improv...
lzx_18570633112 DSP and ARM Processors
X-NUCLEO-IKS01A3 driver for Arduino
Well, I participated in an event and was given a board for free, but the prerequisite was to debug and port it to an MCU, so I wrote the Arduino UNO. Then after I got it, I found that ST actually wrot...
jianshan ST Sensors & Low Power Wireless Technology Forum

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号