EEWORLDEEWORLDEEWORLD

Part Number

Search

MCR01MRTF6190

Description
Fixed Resistor, Metal Glaze/thick Film, 0.063W, 619ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
CategoryPassive components    The resistor   
ManufacturerROHM Semiconductor
Websitehttps://www.rohm.com/
Environmental Compliance
Download Datasheet Parametric View All

MCR01MRTF6190 Overview

Fixed Resistor, Metal Glaze/thick Film, 0.063W, 619ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP

MCR01MRTF6190 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1261641588
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
JESD-609 codee3
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.35 mm
Package length1 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width0.5 mm
method of packingTR, PAPER, 7 INCH
Rated power dissipation(P)0.063 W
Rated temperature70 °C
GuidelineTS 16949
resistance619 Ω
Resistor typeFIXED RESISTOR
size code0402
surface mountYES
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceTin (Sn) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance1%
Operating Voltage50 V
Thick Film Chip Resistors
MCR Series < Not for Automotive application >
Features
1)
2)
Full line up from ultra small size (01005) to 2512 with jumper type.
ROHM resistors have obtained ISO9001/ISO/TS16949 certification.
Datasheet
Size
Part No.
(mm)
0603
1005
1608
2012
3216
3225
5025
6432
(inch)
0201
0402
0603
0805
1206
1210
2010
2512
JRT
4,000
ERT
Paper tape
(4mm pitch)
5,000
Type Code
Packing
Specification
Quantity / Reel
MCR006
MCR01
MCR03
MCR10
MCR18
MCR25
MCR50
MCR100
YRT
Paper tape
(2mm pitch)
MRT
15,000
10,000
Embossed tape
(4mm pitch)
Part Number Description
M C R
Part No.
0 0 6
Size
(mm [inch])
006 (0603 [0201])
01 (1005 [0402])
03 (1608 [0603])
10 (2012 [0805])
18 (3216 [1206])
25 (3225 [1210])
50 (5025 [2010])
100 (6432 [2512])
Y R T
Type Code
J
Resistance Tolerance
D (
±0.5%
)
F (
±1%
)
J (
±5%
)
(Including jumper type)
1 0 0
Nominal Resistance
Resistance code, 3 or 4 digits.
000 denotes jumper type.
Resistance
tolerance
D,F
J
:
:
Resistance
code
4 digits
3 digits
MCR
(Micro chip resistors)
Ex.)
1Ω = 1R0 (
±5%
)
9.1
Ω
= 9R1 (
±5%
)
10
Ω
= 10R0 (
±0.5%,±1%
)
100 (
±5%
)
2.2M
Ω
= 2204 (
±1%
)
225 (
±5%
)
www.rohm.com
c
2015 ROHM Co., Ltd. All rights reserved.
1/6
2015.02 - Rev.F
[Bluesun AB32VG1 RISC-V evaluation board] IDE installation and use
[i=s]This post was last edited by Beifang on 2021-8-9 14:03[/i]1. This board is perfectly compatible with rtthread studio. Follow the manual first, click multiple pictures, and click next. First downl...
北方 Domestic Chip Exchange
【DIY Creative LED】Add touch button and install it on LED lamp
[i=s]This post was last edited by dcexpert on 2020-10-3 17:59[/i]The effect after installing the touch spring and fixing it with hot melt glue. When applying glue, use a USB cable to assist to avoid a...
dcexpert MCU
Know a little about the AD sampling single mode of dsp28335
Three modes are configured: single mode, continuous mode and DMA transfer. Single mode calls the acquisition function once to collect data at a specified AD port, and samples when needed. Continuous m...
fish001 DSP and ARM Processors
[RISC-V MCU CH32V103 Review] - 2: Making an LED flash is not easy
[i=s]This post was last edited by MianQi on 2021-1-28 11:56[/i]Let's look at the wiring first (the tutorial says to directly connect PinA0\PinA1 and LED1\LED2 with jumpers. I'm not used to doing this,...
MianQi Domestic Chip Exchange
SensorTile.box uses air pressure sensors to analyze environmental changes
After the SensorTile.box is flashed with DataLogExtended firmware, the sensor output data waveform can be directly viewed using Unicleo-GUI The following is the data obtained by using the air pressure...
littleshrimp MEMS sensors
When using an oscilloscope probe to measure the AC waveform between the two ends of a component, how should the probe ground wire be connected?
When using an oscilloscope probe to measure the AC waveform between the two ends of a component, if the peak value of the AC voltage of the probe ground wire is 180V and the minimum value is -180V, th...
深圳小花 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号