Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
[i=s]This post was last edited by Li Baiyi on 2019-5-18 18:55[/i] [font=宋体][size=4][color=#333333] The brightness dimming of LED[/color][color=#333333] is achieved by changing the conduction time of t...
I have a question. The circuit board has an external 5V input. The power line is too long, 3 meters. The voltage is too high when it is powered on. Should I use a TVS tube? Or add a filter capacitor? ...
Ask a simple but difficult to answer circuit question: What is the nature of the ground wire GND in the circuit?During the PCB Layout process, engineers will face different GND treatments.Why is this?...
i.MX Linux Development Practical Guide : https://training.eeworld.com.cn/course/5854The first issue - Getting Started with Zero Foundation - 47 episodes The second issue - Kernel Programming - 20 epis...
[backcolor=rgb(222, 240, 251)]I designed an encoder circuit, the circuit is as follows: [/backcolor][backcolor=rgb(222, 240, 251)]Afterwards, when I turned the encoder, there were waveforms on both en...
Circuit Function and Advantages
Ideally, a wireless measurement node has low power consumption, long range, and is easy to interface with different sensors. By using three devices from Analog Devic...[Details]
The 51 series single-chip microcomputer is a high-performance 8-bit single-chip microcomputer launched by Intel Corporation in the United States in 1980. It is widely used in my country. At present, ...[Details]
I recently heard a statement that the digital loop is identical to the analog loop at the output of a power converter . The statement goes like this:
“To the end user, a power supply that uses a ...[Details]
Digital Tube: The digital tube is composed of 7 light-emitting diodes forming a sun shape. If a decimal point needs to be displayed, then add another dot, which becomes an 8-segment digital tube. ...[Details]
When soldering white light (blue light, green light and white light) LED diodes, please strictly follow the following requirements:
1. Workers must wear anti-static gloves and anti-static wrists du...[Details]
The battery life of electric vehicles has always been a topic that has been criticized. The arrival of winter has further exacerbated this concern. The already discounted nominal battery life has bee...[Details]
System clock and frequency division First, a passage from the manual. Three different clock sources can be used to drive the system clock (SYSCLK) HSI Oscillator Clock HSE Oscillator Clock PLL Clo...[Details]
Inspired by the biomechanics of manta rays, researchers have developed an energy-efficient soft robot called the "butterfly robot." Image credit: North Carolina State University
...[Details]
On December 12, according to foreign media reports, as Huawei and the Chinese government bet heavily on 5G, some unknown material suppliers in Japan will profit from it. ...[Details]
Opening remarks:
I have encountered such a project before. Due to the shell effect, the customer deliberately rotated the physical position of the LCD screen 90 degrees counterclockwise. In this case...[Details]
Recently, a medical unit consulted about the application of high-frequency and high-voltage signals in targeted therapy testing. It is necessary to realize the superposition of high-frequency sine wa...[Details]
We have analyzed the BOM table of Huawei Router AX3 Pro. This time we will analyze the number of components and their cost. Device analysis description: Before we start the analysis, we need to exp...[Details]
Abstract: When using a digital oscilloscope to measure waveform parameters, we often encounter inconsistent results between "cursor measurement" and "automatic measurement". Which one is more accur...[Details]
Akamai defends against record-breaking DDoS attack in Asia Pacific (900 Gbps) March 27, 2023 - Akamai Technologies, Inc. (hereinafter referred to as: Akamai), the cloud service provider responsible...[Details]
The controller is a main command device that changes the wiring of the main circuit or control circuit and the resistance value in the circuit in a predetermined order to control the starting, spee...[Details]
GD32 MCU
京公网安备 11010802033920号
EEWORLD
